Idiomas disponibles
Idiomas disponibles
Symbol
power tool designation
The power tool is intended for dry cutting, grinding and
sanding of metals (and other materials)�
The area of the tool application can be expanded due
to use of additional accessories�
There is a possibility of a stationary installation of the
power tool by use of some special accessories�
Power tool
components
1
Reducer
2 Spindle lock
3 Ventilation slots
4 Protective casing
5 Additional handle
6 Body
7 On / off switch
8 Lock-off button
9 Wrench *
10 Flange wrench *
11 Cap *
12 Mounting lug
13 Screw
14 Casing bolt
15 Spindle
16 Flange
17 Disc *
18 Clamping nut
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation
of power tool elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Additional handle (see fig. 1)
Always use the additional handle 5 when operating�
Additional handle 5 may be positioned as deemed
comfortable by the user�
• Release additional handle 5 as shown on fig. 1.
• Extract cap 11 and screw additional handle 5 into
the threaded opening�
• Insert cap 11 into the freed threaded opening�
Meaning
Do not dispose of the power
tool in a domestic waste
container�
DWT
Protective casing
Always use protective casing 4 when
applying cutting and grinding discs.
Operation of the aforementioned ac-
cessories without protective casing 4
is strictly forbidden. Protective casing 4 should al-
ways face the operator with its closed part.
Mounting / dismounting the protective casing (see
fig. 2)
[WS13-150 T]
• With a screwdriver (not supplied with the power tool)
release screw 13 and install protective casing 4 onto the
spindle neck, watching that mounting lug 12 comes into
the longitudinal groove of the spindle neck (see fig. 2).
• Turn protective casing 4 into the required position
and tighten screw 13 with a screwdriver (not supplied
with the power tool)�
• When dismounting protective casing 4 repeat the
aforementioned operations in reverse order�
[WS13-180 T, WS13-180 D]
• With wrench 9 release bolt 14 and install protective
casing 4 onto the spindle neck, watching that mounting
lug 12 comes into the longitudinal groove of the spindle
neck (see fig. 2).
• Turn protective casing 4 into the required position
and tighten bolt 14 with wrench 9�
• When dismounting protective casing 4 repeat the
aforementioned operations in reverse order�
Mounting / replacement of accessories
After mounting accessories of any kind,
make a trial run before commencing op-
eration - start the power tool and let it
work in idle mode for not less than 30
seconds. The operation of accessories with radial
or axial run-out and causing increased vibration of
the power tool is strictly forbidden.
Wearing protective gloves is recom-
mended for mounting / replacing acces-
sories.
Mounting of cutting / grinding disc (see fig. 3)
• Install flange 16 onto spindle 15 (see fig. 3).
• Install one of the aforementioned accessories onto
spindle 15�
• Press and hold spindle lock 2�
• Screw clamping nut 18 onto spindle 15 and tight-
en it with flange wrench 10� Attention: at mounting
any accessories over 4 mm thick clamping nut 18
should be turned over (see fig. 3).
• Release spindle lock 2�
Replacing the cutting / grinding disc (see fig. 3-4)
• Press and hold spindle lock 2�
• Release clamping nut 18 with flange wrench 10 (see
fig. 4).
• Replace the accessory�
• Screw clamping nut 18 onto spindle 15 and tight-
en it with flange wrench 10� Attention: at mounting
English
21
