Idiomas disponibles
Idiomas disponibles
power tool, if they are not supervised or instructed
about use of the power tool by a person responsible
for their safety�
• Do not force the power tool. Use the correct
power tool for your application� The correct power
tool will do the job better and safer at the rate for which
it was designed�
• Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired�
• Disconnect the plug from the power source and /
or the battery pack from the power tool before mak-
ing any adjustments, changing accessories, or
storing power tools� Such preventive safety measures
reduce the risk of starting the power tool accidentally�
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users�
• Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's op-
eration. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools�
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control�
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the work
to be performed. Use of the power tool for operations
different from those intended could result in a hazard-
ous situation�
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations�
• Note that when you operate a power tool, please
hold the auxiliary handle correctly, which is helpful
when controlling the power tool� Therefore, proper
holding can reduce the risk of accidents or injuries�
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained�
• Follow instruction for lubricating and changing ac-
cessories�
safety warnings
Safety warnings common for grinding, sanding,
wire brushing, polishing or abrasive cutting-off op-
erations:
• This power tool is intended to function as a
grinder, sander, wire brush, polisher or cut-off tool.
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and / or serious injury.
• Operations such as grinding, sanding, wire
brushing, polishing or cutting-off are not recom-
mended to be performed with this power tool. Op-
Special
erations for which the power tool was not designed
may create a hazard and cause personal injury�
• Do not use accessories which are not specifical-
ly designed and recommended by the tool manu-
facturer. Just because the accessory can be attached
to your power tool, it does not assure safe operation�
• The rated speed of the accessory must be at
least equal to the maximum speed marked on the
power tool. Accessories running faster than their rat-
ed speed can break and fly apart.
• The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately guarded or controlled�
• The arbour size of wheels, flanges, backing
pads or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control�
• Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive wheels
for chips and cracks, backing pad for cracks, tear
or excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped, in-
spect for damage or install an undamaged acces-
sory. After inspecting and installing an accessory,
position yourself and bystanders away from the
plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time�
• Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron ca-
pable of stopping small abrasive or workpiece frag-
ments. The eye protection must be capable of stopping
flying debris generated by various operations. The dust
mask or respirator must be capable of filtrating particles
generated by your operation� Prolonged exposure to
high intensity noise may cause hearing loss�
• Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation�
• Hold the power tool by insulated gripping sur-
faces only, when performing an operation where
the cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock�
• Position the cord clear of the spinning accesso-
ry. If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory�
• Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning ac-
cessory may grab the surface and pull the power tool
out of your control�
• Do not run the power tool while carrying it at
your side. Accidental contact with the spinning acces-
sory could snag your clothing, pulling the accessory
into your body�
• Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards�
• Do not operate the power tool near flammable
materials. Sparks could ignite these materials�
English
18
