Idiomas disponibles
Idiomas disponibles
Table of contents
Safety Precautions ................................................................... 2
Français............................................................................. 16
Español ............................................................................. 20
General Description ................................................................. 4
Operation ................................................................................... 4
Setup ................................................................................... 4
Preparing to Paint................................................................ 5
Painting ............................................................................... 6
Operating the Front Caster.................................................. 6
Pressure Relief Procedure .................................................. 6
cleanup ..................................................................................... 7
Cleaning the Spray Tip ........................................................ 7
Maintenance .............................................................................. 7
General Repair and Service Notes...................................... 7
Maintaining the Engine ........................................................ 8
Cleaning or Replacing the Filters ........................................ 8
Replacing the PRIME/SPRAY Valve ................................... 9
Replacing the Pump ON/OFF Switch .................................. 9
Replacing the Gears and/or Slider Assembly...................... 9
Replacing the Transducer ................................................. 10
Servicing the Clutch Assembly .......................................... 10
Servicing the Fluid Section ................................................ 13
Troubleshooting ..................................................................... 15
Parts Listings .......................................................................... 48
Main Assembly .................................................................. 48
Drive Assembly ................................................................. 50
Fluid Section Assembly (PL1800M) .................................. 52
Fluid Section Assembly (PL2800M) .................................. 54
Cart Assemblies ................................................................ 56
Front Wheel Assemblies ................................................... 58
Gun Holder Assembly ....................................................... 60
Brake Assembly (PL2800M).............................................. 60
Siphon Assembly............................................................... 60
Accessories ....................................................................... 62
Limited Warranty .................................................................... 64
General Description
This airless line striper is a precision power tool used to spray
many types of material for many types of applications including
parking lots, curbs, and athletic fields. Read and follow this
instruction manual carefully for proper operating instructions,
maintenance, and safety information.
Gun
Trigger
Material
Hose
Airless
Sprayer
Gun Holder
Assembly
Spray Gun
Operation
This equipment produces a fluid stream at
extremely high pressure. Read and understand the
warnings in the Safety Precautions section at the
front of this manual before operating this
equipment.
English
Caster Trigger (PL2800 only)
Siphon Hose
Return Hose
Engine
PRIME/
SPRAY
Valve
Front
Caster
Assembly
Tip Assembly
Setup
Perform the following procedure before starting the engine of a
gas-powered line striper.
1. Ensure that the siphon hose
and the return hose are
attached and secure.
2. Position the spray gun.
a.
Loosen the support bar
clamp hex screw and
rotate the gun support bar
to the desired position.
Tighten the hex screw
securely.
b.
Loosen the gun holder
clamp knob and slide the
spray gun to the desired
vertical and horizontal
(front-to-back) position.
Tighten the knob securely.
3. Turn the pressure control knob fully counterclockwise to
its lowest pressure setting.
4. Make sure the pump ON/OFF switch is in the OFF
position.
5. Fill the fluid section oil cup with approximately one
tablespoon of piston seal lubricant (Piston Lube).
NOTE: The height of the spray gun affects the width
of the spray pattern (i.e., the lower the gun, the
smaller the line width). Tip size also affects line
width.
IMPORTaNT: Never operate unit for more than ten seconds
without fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
7. Check the engine oil level. The gasoline engine oil level
is determined by the manufacturer. Refer to the engine
manufacturer's service manual (supplied).
8. Close the fuel shut-off lever and fill the gas tank with
gasoline. Use only high quality, unleaded gasoline.
NOTE: The gun support bar and the spray gun can be
mounted on either side of the sprayer. To move
the gun support bar:
a. Remove the support bar clamp hex screw and
nut.
b. Move the gun support bar to the opposite side of
the cart.
c. align the support bar clamp with the bracket on
the cart.
d. Thread the clamp hex screw through the gun
support bar clamp and the bracket on the cart.
Place the nut on the end of the clamp hex screw
and tighten securely.
adjusting the Trigger Tension
Use the following procedure to adjust the spring tension of the
trigger lever on the gun holder assembly. The trigger lever
pulls and releases the spray gun trigger when operated from
the trigger on the cart. The proper tension ensures that the gun
will shut off when the gun trigger is released. To ensure proper
tension, there should be approximately a 1/32" to 1/16" gap
between the trigger lever and the spray gun trigger.
IMPORTaNT: always keep the trigger lock on the spray
gun in the locked position while making adjustments to the
system.
1. Using a wrench, loosen the bolt on the cable block.
2. Move the cable block in the appropriate direction to create
a gap of 1/32" to 1/16" between the trigger lever and spray
gun trigger.
a.
Slide the cable block toward the gun to increase the gap
between the trigger lever and spray gun trigger.
4
Gun Support
Bar Clamp
Clamp
Hex Screw
Cable
Block
Gun Holder
Clamp Knob
© Titan Tool Inc. All rights reserved.
