Idiomas disponibles
Idiomas disponibles
•
Reaching into the running saw blade (cut inju-
ries).
•
Kick-back of workpieces and parts of workpi-
eces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if ear-muffs are not used
as necessary.
•
Harmful emissions of wood dust when used
in closed rooms.
4. Technical data
AC motor: ................................220-240 V ~ 50Hz
Power: ................. 1500 W S1 / 1800 W S2 5 min
Idle speed n
: ......................................4900 min
0
Carbide saw blade: ...........ø 210 x ø 30 x 2.8 mm
Maximum tooth pitch: ................................. 3 mm
Number of teeth: ............................................ 48
Swiveling range: ........................... -47° / 0° / +47°
Miter cut to the left: .................................0° to 45°
Miter cut to the right: ...............................0° to 45°
Saw width at 90°: ............................ 310 x 62 mm
Saw width at 45°: ............................ 210 x 62 mm
Saw width at 2 x 45°
(double miter cut left): ...................... 210 x 36 mm
Saw width at 2 x 45°
(double miter cut right): ................... 210 x 25 mm
Weight: .......................................... approx. 11 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: .......................................... ≤ 1 mW
Protection class: ........................................... II/
Minimum workpiece size: Only ever cut workpie-
ces which are big enough to clamp securely with
the clamping device – minimum length 160 mm.
A load factor of S2 5 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (1800
W) for no longer than the time stipulated on the
specifi cations label (5 min). If you fail to observe
this time limit the motor will overheat. During the
OFF period the motor will cool again to its starting
temperature.
Danger!
Noise
The noise emission values were measured in ac-
Anl_TC_SM_2131_2_Dual_SPK13.indb 23
Anl_TC_SM_2131_2_Dual_SPK13.indb 23
GB
cordance with EN 62841.
L
sound pressure level ....................... 96 dB (A)
pA
K
uncertainty ....................................... 3 dB (A)
pA
L
sound power level ........................ 109 dB (A)
WA
K
uncertainty ....................................... 3 dB (A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
-1
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
- 23 -
30.03.2023 14:47:15
30.03.2023 14:47:15
