Idiomas disponibles
Idiomas disponibles
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1.
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2.
Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3.
Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
ASSEMBLY
WARNING:
Always be sure that the lock key
and battery cartridge are removed before carrying
out any work on the mower. Failure to remove the
lock key and the battery cartridge may result in seri-
ous personal injury from accidental start-up.
WARNING:
Never start the mower unless it is
completely assembled. Operation of the machine
in a partially assembled state may result in serious
personal injury from accidental start-up.
Installing the battery cover
WARNING:
Do not insert the lock key and bat-
tery cartridge before installing the battery cover.
Failure to do so may cause a serious injury.
Install the battery cover completely before the opera-
tion. The battery cover protects the mower and battery
cartridge from mud, dirt, and water.
Place the battery cover with the protrusions on the
1.
mower aligned with the holes on the battery cover.
► Fig.1: 1. Protrusion 2. Hole 3. Battery cover
Place your hands in the middle of the battery
2.
cover and push it.
► Fig.2
Before the first operation, check that the pivot
3.
point of the battery cover is attached properly. If the
battery cover is installed correctly, it will not open until
the battery cover locking lever is pulled.
► Fig.3: 1. Pivot point 2. Battery cover locking lever
Installing the handle
NOTICE:
When installing handles, position the
cords so that they are not caught by anything
between the handles. If the cord is damaged, the
mower switch may not work.
1.
Slide the both ends of lower handle into the
grooves of the mower then fully tighten the clamping
screws.
► Fig.4: 1. Clamping screw 2. Lower handle
2.
Align the screw holes of upper handle and lower
handle. Secure them with the clamping screws and
nuts.
► Fig.5: 1. Clamping nut 2. Clamping screw
NOTE: Hold the upper handle firmly so that it does
not drop off your hand.
3.
Attach the holders to the handle. Position the
power supply cord as shown in the figure.
► Fig.6: 1. Holder
Removing the mulching plug
Optional accessory
1.
Open the rear cover.
► Fig.7: 1. Rear cover
Hold the mulching plug by the handle, and then
2.
pull it out from the mower body as shown in the figure.
► Fig.8: 1. Mulching plug 2. Handle
Installing the grass basket
1.
Open the rear cover.
► Fig.9: 1. Rear cover
2.
Hook the grass basket on the rod of the mower
body as shown in the figure.
► Fig.10: 1. Hook 2. Rod 3. Grass basket
Attaching the mulching plug
Optional accessory
1.
Open the rear cover, and then remove the grass
basket.
► Fig.11: 1. Rear cover 2. Grass basket
Hold the mulching plug by the handle, and then
2.
attach it to the mower body as shown in the figure.
► Fig.12: 1. Mulching plug 2. Handle
11 ENGLISH
