Idiomas disponibles
Idiomas disponibles
carefully re-enter the cut. The wheel may bind, walk up
or kickback if the power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
f) Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
ADDITIONAL SAFETY INSTRUCTIONS
GENERAL
•
This tool is not suitable for wet grinding/cutting
Only use the flanges which are supplied with this tool
•
•
This tool should not be used by people under the age of
16 years
•
Remove battery from tool before making any
adjustments or changing accessories
ACCESSORIES
•
SKIL can assure flawless functioning of the tool only
when original accessories are used
•
For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
•
Use only grinding/cutting discs with a maximum
thickness of 6 mm and a spindle hole diameter of
22 mm
Never use reducors or adaptors to fit large-hole grinding/
•
cutting discs
•
Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
•
Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
BEFORE USE
•
Before using the tool for the first time, it is recommended
to receive practical information
•
Always mount auxiliary handle E 2 and protective guard
F 2 ; never use the tool without them
•
Use suitable detectors to find hidden utility lines
or call the local utility company for assistance
(contact with electric lines can lead to fire or electrical
shock; damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
•
Do not work materials containing asbestos (asbestos
is considered carcinogenic)
•
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
•
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
•
Follow the dust-related national requirements for the
materials you want to work with
•
Be careful when cutting grooves, especially in supporting
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be observed
under all circumstances)
•
Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
•
Do not clamp the tool in a vice
DURING USE
In case of electrical or mechanical malfunction,
•
immediately switch off the tool and remove battery
•
In case of a battery protection cut off, or when the
battery is removed, the tool will not restart on its own; for
restarting the tool unlock on/off switch and switch on tool
again w
AFTER USE
•
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
BATTERIES
•
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
•
Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
•
Do not use the battery when damaged; it should be
replaced
•
Do not disassemble the battery
•
Do not expose tool/battery to rain
•
Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Wear protective glasses and hearing protection
5 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
6 Store tool/charger/battery in locations where temperature
will not exceed 50°C
7 Do not dispose of electric tools and batteries together
with household waste material
USE
•
Charging battery
! read the safety warnings and instructions
provided with the charger
•
Removing/installing the battery 2
•
Battery level indicator 8
- press the battery level indicator button L to show the
current battery level.
•
Mounting of accessories 2
! remove battery from tool
- clean spindle A and all parts to be mounted
- tighten clamping flange B with spanner C while pushing
spindle-lock button D
! push spindle-lock button D only when spindle A is
at a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! never use a grinding/cutting disc without the label
("blotter") which is glued onto it (if provided)
Mounting of auxiliary handle E 9
•
! remove battery from tool
12
