Idiomas disponibles
Idiomas disponibles
Notes for Wet Vacuuming and
for Vacuuming with Shampoo
CAUTION:
• Do not fill foaming shampoos into the shampoo tank!
• Always remove the permanent filter when vacuuming
liquids.
• Before the cleaner is used again for dry vacuuming, all
components must be dry.
Immediately switch off the appliance in the following
situations:
• During foaming
• If liquid escapes
• When the vessel is full.
• When the appliance falls over.
NOTE:
• The collection vessel can hold approx. 10 litres of liquid
(without foaming).
• If foam should form in the collection vessel, then the
maximum capacity is only 1.5 litres!
• When the vessel is full the float valve closes the suction
aperture and the motor runs at a higher speed. Switch
the appliance off immediately and empty it.
Operation
Preparation
1. Unwind the lead completely.
2. Check if the mains voltage that you want to use matches
the information on the rating plate.
CAUTION:
Take note of the range limited by the length of the cable!
3. Open the locking mechanisms.
4. Remove the engine housing using the handle.
5. If the protective filter has not yet been mounted, attach
it as described in chapter "Notes on Use" "Protective
Filter Made of Foam".
CAUTION:
Check that the protective filter fits properly.
Dry Vacuuming
1. Attach the permanent filter as described in chapter "Notes
on Use" "Permanent Filter".
2. Attach the motor housing.
3. Close the locking mechanisms.
4. Attach the wet / dry brush or the crevice nozzle to the
suction pipe or directly to the suction hose.
5. Connect the mains plug to a properly installed earthed
socket.
6. Set the On / Off switch to I.
7. Vacuum at a steady speed. There is no need to exert
pressure.
BSS6000CB
Wet Vacuuming
1. Disconnect the mains plug from the socket.
2. Remove the permanent filter.
3. Attach the motor housing.
4. Close the locking mechanisms.
5. Attach the wet / dry brush to the suction pipe or directly to
the suction hose.
6. Connect the mains plug to a properly installed earthed
socket.
7. Set the On / Off switch to I.
Vacuuming with Shampoo
NOTE:
• Dose as indicated on packaging or instruction leaflet.
• Furthermore, refer to the instructions for carpets or
upholstery in order to avoid damaging them.
• Test your appliance beforehand at an insignificant spot.
Installation of the Shampoo Accessory
1. Disconnect the mains plug from the socket.
2. Attach the shampoo or upholstery brush to the suction
pipe or directly to the suction hose. Insert the hose of the
brush into the connector of the shampoo hose.
3. The bottom end of the shampoo hose must be connected
to the engine housing. You find symbols at the shampoo
house and engine housing ( + ). Attach the shampoo
hose to the engine housing in such a way that the sym-
bols are facing each other. Tighten the shampoo hose by
turning it clockwise.
4. There is another hose at the shampoo tank. Attach it in
the same way as previously described.
NOTE:
Make sure the shampoo hose has no kinks!
Handling
1. Remove the permanent filter.
2. Attach the motor housing.
3. Close the locking mechanisms.
4. Fill the shampoo tank with water and cleaning shampoo.
Do not fill more than 3 L. There is a marking on the
shampoo tank.
5. Connect the mains plug to a properly installed earthed
socket.
6. Set the On / Off switch to II.
7. Use the spray device lever on the suction hose to release
the shampoo.
Dismantling of the Shampoo Accessory
1. Disconnect the mains plug from the socket.
2. In order to remove the brush, press down the bottom of
the connector at the shampoo hose. Remove the hose.
3. Remove the hose ends from the engine housing by turn-
ing them counterclockwise.
45
17.10.17
