Idiomas disponibles
Idiomas disponibles
CLEANING
BLADES
To clean the blades, fill a flat dish with Oster™ Blade Wash
DO NOT IMMERSE THE APPLIANCE. Turn «ON» (|) the appliance with the blades facing down. Do not hold the
appliance upright when cleaning blades with the appliance plugged in. Listen for a change in the hum of the
motor. As the build-up is removed, the clean blade runs faster and at a higher pitch. When the pitch stabilizes
(between 30 to 60 seconds), turn «OFF» the appliance and unplug. Remove from the cleaning solution and, while
holding the appliance with the blade end facing down, wipe the blades dry with a clean, dry cloth. Re-oil blades.
Always unplug the appliance when carrying out other cleaning and do not immerse the appliance body, charging
stand, adapter, power cord or plug in water or any other liquid.
CHARGING STATION
1. Disconnect the charging station from the power supply.
2. If necessary, remove hairs from both charging cavities.
3. If dirty, clean the contacts with a dry cloth.
CONTACTS
If required, clean the contacts of the batteries and the clipper with a dry cloth.
Any maintenance beyond the cleaning and lubricating instructions in this manual should be performed by an
Oster™ Authorized Service Center.
WARNING
When using or cleaning this appliance, do not use any aerosol sprays or blade washes,
especially those containing methylene chloride, dimethyl benzyl ammonium chloride, or 1-1-1
trichloroethylene. Damage caused by these chemicals will void your warranty. You may use
Oster
approved blade washes, lubricants and disinfectant sprays that do not harm the product.
TM
076076-810_076076-910_078005-210_21ESFM2.indd 8-9
076076-810_076076-910_078005-210_21ESFM2.indd 8-9
English
cleaning solution and immerse only the blade teeth.
®
8
TROUBLE SHOOTING
The tasks described here for troubleshooting can be done mostly by the operator.
Some tasks only may be done by specially trained personnel or by an Oster
tasks are marked with (*).
MALFUNCTION
CAUSE
Top blade does not move Clipper-head is not well engaged
Drive carrier is defective
Clipper cuts badly or not
Clipper blade is blunt
at all
Clipper blade have not been
correctly grounded
Clipper blades are not oiled
Hairs jammed between top and
bottom blades
Clipper-head has too little clipping
pressure
Motor is not running
Battery is not charged
Contacts dirty
Faulty battery
Smell of burning from the motor
housing. Motor burned out
Motor and / or electronics faulty
Clipper-head blocked
Motor runs very slowly
Clipper blades were not oiled
sufficiently
Running time of a fully
Clipper blades were not oiled
charged battery is too
sufficiently
short and / or blades are
Battery is not fully charged, or
getting hot
faulty battery is being used
When battery is
Contacts dirty
unloaded the light does
Faulty battery
not change from green
Contacts of the charging station are
to red
deformed
English
TM
authorized service center. These
RECTIFICATION
Engage the clipper-head correctly when the
motor is running
Replace drive carrier (*)
Have top and bottom blades re-sharpened by
Oster
authorized service center
TM
Oil clipper blades every 15 minutes
Take off clipper-head, push the top blade half
away from the clipper head, take away hairs
between top and bottom blade
Have clipper-head inspected (*)
Charge battery
Switch clipper «OFF» (O) and clean the
contacts
Replace battery (*)
Have motor and / or electronics replaced (*)
Have motor and / or electronics replaced (*)
Clean and oil clipper-head
Oil clipper blades
Oil clipper blades
Only use intact, fully charged original batteries
Clean contacts
Replace battery (*)
Have the charging station repaired (*)
9
5/27/21 10:35
5/27/21 10:35
