Idiomas disponibles
Idiomas disponibles
5. Hold the charger firmly with one hand and pull the clipper or the battery out with the other.
6. Note: Except when charging, always unplug this appliance from the electrical outlet immediately after using.
ABOUT THE LI-ION BATTERY
1. This appliance operates with a removable Li-Ion 3.6V 3000mAh battery.
2. Note: To ensure that the new battery reaches its full potential, the battery should be completely drained after
the first use. This operation will only have to be performed once.
3. It will take no more than 100 minutes for the battery to be fully charged when fully discharged.
4. To ensure the longevity of this powerful battery the clipper must be operated with properly cleaned, sharpened
and oiled blades at all times.
5. When the battery is fully charged, the clipper can be used for 120 minutes for the Cordless Classic 76, or 80
minutes for the Cordless Turbo A5, without being connected to the power supply.
6. For instructions on disposal of the Li-Ion battery please refer to the "WASTE DISPOSAL" section at end of this
manual.
CHANGING THE BATTERIES
1. Move the switch to the off position.
2. Push the battery interlock on the back side of the clipper, and pull the battery out of the
clipper.
3. Fit the charged battery in the clipper, until the battery interlock is engaged (Figures 4
and 5).
OPERATING THE UNIT
The appliance is designed to operate in either cordless or corded mode. The preferred method is cordless as it
ensures a longer life for the battery. Use the power cord when the batteries are not fully charged. If your appliance
did not come with a charging stand please refer to corded operation in this manual.
Always apply one to two drops of the provided Oster
lubricant to the blades before use. Wipe off excess with a clean dry cloth. When finished using, clean excess
hair from the blades using the cleaning brush and wipe the housing with a clean dry cloth. Before replacing the
blade guard for storage, disperse one or two drops of lubricating oil over the blades to prevent rusting. Cutting
efficiency may drop and the blades and motor may be damaged if hair is dirty or hair styling agents have been
applied. Always ensure that hair is clean before using the appliance.
Keep the cord straight while in use. If the cord becomes kinked or tangled, turn «OFF» the appliance and
straighten it.
CORDLESS OPERATION
1) Remove the appliance from the charging stand. (See section titled "HOW TO CHARGE THE UNIT" before initial
use).
2) Turn the appliance «ON» (|) using the switch located on the front of the unit and use the appliance. If the
appliance does not turn «ON» (|), then the battery may be fully depleted and may have to be partially charged
prior to re-use. Follow the charging procedure and let the battery charge for approximately 100 minutes.
3) Turn the appliance «OFF» (O) when finished using.
4) Insert appliance into charging stand or plug into the power cord.
076076-810_076076-910_078005-210_21ESFM2.indd 6-7
076076-810_076076-910_078005-210_21ESFM2.indd 6-7
Figure 4
TM
Clipper & Blade Lubricating Oil or other Oster
TM
6
English
STORAGE
1) Store your appliance in a clean, dry space.
2) Do not wrap the cord around the appliance when storing. This can damage the cord insulation.
3) Always take care not to tangle the cord while using or storing the appliance.
4) We recommend storing the appliance and cord in the original carton when not in use.
DETACHABLE BLADE CLIPPERS
REMOVING OR REPLACING BLADES
IMPORTANT: Make sure the appliance is turned off and unplugged before removing any part.
TO REMOVE:
Cordless Turbo A5 has a locking mechanism. To remove, push in locking mechanism
below the heel of the blade to release the blade, then lift blade away from clipper and slide
off tongue.
Cordless Classic 76 does not have a locking mechanism. To remove, lift the blade away
from clipper and slide off tongue.
Figure 5
TO REPLACE:
Turn motor «ON» (|); insert blade on tongue fully then snap blade into place.
LUBRICATING THE BLADES
approved
Blades should be oiled regularly to reduce heat, maintain sharpness and will extend run time per battery charge
cycle by reducing friction. Before removing the blade, be sure it has cooled down and the appliance is unplugged.
Carefully slide the upper blade left or right to apply one or two drops of provided Oster
Lubricating Oil or other Oster
hair to stick between teeth, slowing or jamming blades. Wipe excess oil with a dry, soft cloth.
BLADE SHARPENING
Oster™ cutting blades are of individual hollow-ground design, hardened to extend cutting life. As with any cutting
instrument, the cutting edges will become dull with usage. Increasing blade tension to force dull blades to cut
can cause the appliance to heat and reduce motor life, and further shorten blade life. When the cutting blades no
longer cut smooth and clean, sharpening is necessary.
When sharpening blades becomes necessary, send blades to an Oster™ Authorized Service Center where
approved methods, equipment and proper knowledge are used to restore the original hollow-ground design and
cutting ability. DO NOT sharpen blades by flat grinding or any method contrary to the design and construction of
Oster™ cutting blades.
MAINTENANCE
BLADE CARE
approved lubricant on each running rail of the lower blade. Excess oiling will cause
TM
7
English
Clipper & Blade
TM
5/27/21 10:35
5/27/21 10:35
