Idiomas disponibles
Idiomas disponibles
8. CONNECTION TO THE MAINS
1.
Ensure that mains voltage and frequency are the same as those stated on the rating plate (A) attached
to the appliance. . Ensure that the supply socket has the following characteristics:
2
earthed.
b)
It fulfils the requirements of the rated current as set out on the rating plate.
with the IEC regulations: - magnetothermal differential switch with In = nominal value as stated on the
rating plate; - Differential with Id sensitivity = 30 mA. . Ensure that there is no danger of explosion (AD)
in the room.
4.
The connecting cable to the appliance is H05 VVF, designed for internal use. For
installation in any other environments, it will be necessary to change the cable with the appropriate type
(for example H07 VVF for external use).
placed by mistake in a horizontal position or has been turned upside down, leave for at least three hours
in the correct position before switching on the power supply. .Connect the plug (do not use three-way
adapters and reduction adapters) (see figure 7).
9. CONTROLS
The controls of the appliance are located at the front inside a protected panel.
the rotary shelves into motion. Rotation stops when the door is opened or when even the slightest
obstacle is encountered.
2. Light switch:
switch:
to switch on the refrigeration system.
appliance.
Thermostat:
to adjust the temperature in the appliance. To adjust temperature:
a) Press button
5 "SET or P"
pressing button
6 "UP"
or button
10. CHECKING CORRECT OPERATION BEFORE USE
Check that: 1
. The plug is connected. . The refrigeration unit switch is switched on (green light on).
3
. The thermometer shows the desired temperature for the goods to be stored. . The internal lights and
the rotation are on.
5.
The door is properly closed. . The appliance is not exposed to direct sunlight or to
high-powered lamps. . The room temperature does not exceed that in which the appliance is designed
7
to work normally, i.e. +30°C, 55% r.h. (climatic class 4). . There is suitable clearance (at least 30 cm) in
front of the motor grille to ensure sufficient airflow. . The cabinet is suitably filled, without overloading the
shelves and with sufficient space for cold air circulation.
11. INTERNAL CLEANING (EVERY 15 DAYS)
1.
Switch off the appliance. . Open the door and remove the refrigerated goods.
accessories with a sponge dipped in water with a little sodium bicarbonate. Dry with care.
12. REPLACING THE INTERNAL LIGHTS
1.
Switch off the appliance. . Undo the screws which hold the top lamp socket in place. . Detach the
fluorescent tube with its protective cover from the top lamp socket. . Take the tube out of the bottom
lamp socket.
5.
Remove the protective cover. . Replace the fluorescent tube.
the above instructions in reverse order (see figure 9).
13. REPLACING THE DOOR'S MAGNETIC GASKET
1.
Open the door.
2.
Take hold of the magnetic gasket and pull it out of the frame.
gasket and press it firmly down all around (see figure 10).
Operator's guide
3
N.B.
If during transport or storage the appliance has been
to switch on the light inside the appliance.
4. Thermometer:
once to display the temperature set-point, which can be changed by
7 "DOWN"
(see figure 8).
2
6
9
2
2
6
7
5
1. Rotation switch:
to display the temperature in the
4
8
4
7.
Reassemble by following
a)
it is properly
c)
It complies
it sets
3. Refrigeration
3
. Wipe the sides and
3
3.
Insert the new
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO
