Idiomas disponibles
Idiomas disponibles
OPERATION
1. INSTALLING AND REMOVING THE
BATTERY PACK(SEE FIG. B)
A) TO REMOVE THE BATTERY PACK
Depress the Battery Pack Release Button firmly first and
then slide the Battery Pack out from your tool.
B) TO INSTALL THE BATTERY PACK
Slide the fully charged Battery Pack onto the tool with
sufficient force until it clicks into position.
2. ON / OFF SWITCH (SEE FIG. C)
Depress the On/Off switch to start and release it to stop
your drill.
The on/off switch is fitted with a brake function which stops
your chuck immediately when you quickly release the switch.
It is also a variable speed switch that delivers higher speed
and torque with increased trigger pressure. Speed is
controlled by the amount of switch trigger depression.
WARNING: Do not operate for long
periods at low speed because excess
heat will be produced internally.
3. SWITCH LOCK (SEE FIG. C)
The switch trigger can be locked in the OFF position. This
helps to reduce the possibility of accidental starting when
not in use. To lock the switch trigger, place the rotation
control in the center position.
4. REVERSIBLE (SEE FIG. C)
For drilling and screw driving use forward rotation marked
"
" (lever is moved to the left). Only use reverse rotation
marked "
" (lever is moved to the right) to remove
screws or release a jammed drill bit.
WARNING: Never change the direction
of rotation when the chuck is rotating,
wait until it has stopped!
5. TWO-SPEED GEAR CONTROL (SEE FIG. C)
The drill has a two-speed gear control designed for drilling
or driving at LO (mark is 1) or HI (mark is 2) speeds. A slide
switch is located on top of the drill to select either LO or
HI speed. When using the drill in the LO speed range, the
speed will decrease and the drill will have greater power and
torque. When using the drill in the HI speed range, the speed
will increase and the drill will have less power and torque.
GEAR I
Low speed range: for screwdriving or working with large
drilling diameter.
GEAR II
High speed range: for working with small drilling diameter.
WARNING: To prevent gear damage,
always allow the chuck to come to a
EN
complete stop before changing the direction
of rotation or the two-speed gear control.
6. AUTOMATIC SPINDLE LOCK
The automatic spindle lock allows you to use it as a regular
screwdriver. You can give an extra twist to firmly tighten a
screw, loosen a very tight screw or continue working when
the battery energy has expired. For manual screwdriver
purposes, the chuck is automatically locked when the tool
is off.
7. CHUCK ADJUSTMENT (SEE FIG. D)
Rotate the front section of the chuck to open the jaws. Insert
the drill bit, taking care to ensure the drill bit is in the centre
of the chuck jaws. Rotate the front section of the chuck in
the opposite direction until the drill bit is firmly clamped.
8. TORQUE ADJUSTMENT (SEE FIG. E)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque adjustment
ring. The torque is greater when the torque adjustment ring
is set on a higher setting. The torque is less when the torque
adjustment ring is set on a lower setting.
1-6
for driving small screws
7 - 12
for driving screws into soft material
13 - 18
for driving screws into soft and hard material
for heavy drilling
9. USING THE SIGHT LIGHT
To turn on the light, press the on/off switch and make sure
the forward/reverse rotation control is on right/left position.
When you release the on/off switch, the light will be off.
LED lighting increases visibility - great for dark or enclosed area.
The LED is also a battery capacity indicator. It will flash
when the battery power is low.
When LED flashes, remove the battery and recharge.
10. BELT CLIP (SEE FIG. F)
Screw the Belt Clip on the tool with the screw provided in
the plastic bag. The belt clip can be cliped on your belt or
pocket, etc.
11. DRILLING
To activate the drill function (for drilling metal wood or
plastic), turn the torque adjustment ring on the drill position.
When drilling in metal, only use HSS drill bits
in good condition. Always use a magnetic
bit holder (not included) when using short
screwdriver bits. When screwdriving, apply a
small quantity of liquid soap or similar to the
17
