40980.M
System
In general, the IPo2W system allows video door entry
devices to communicate with each other via the TCP/
IP protocol, using a connection over non-polarised 2-wire
cables.
The system can also interface with IP cameras via Wi-Fi.
The system offered is composed of:
- Outdoor Station. One outdoor station can be connected.
The outdoor station can be configured to communicate
with two apartments.
- Indoor Station. One or two indoor stations can be
installed in an apartment.
- System power supply unit. A power supply unit can
power one outdoor station and two indoor stations per
apartment, for up to two apartments.
Assuming that the system power supply unit is the device at
the centre of the video door entry system, outdoor stations
and indoor stations can be connected to the power supply
unit with a star topology, a daisy-chain connection (or input
to output) or a mixed connection (star and daisy-chain).
Indoor Station
Functions
•
7" capacitive touch screen monitor
• IEEE 802.11 b/g/n 2.4GHz Wi-Fi connectivity
• Possibility of receiving firmware upgrades via OTA
(Over The Air)
• Remote calls via the VIEW Door app on one or more
smartphones
• Actuator enable/disable (powered lock and gate relay
or other actuator)
• Internal flash memory and micro SD card support
• Automatic and manual video/picture recording
• Voice message
• Intercom function between indoor stations of the same
family and between indoor stations of different families
• Full-duplex audio with echo cancellation and noise
reduction functions
• Adjustable conversation and ringtone volumes
• Adjustable ringtone duration (for outdoor station,
intercom, landing)
• Selectable ringtone (for outdoor station, intercom,
landing)
• "Do not disturb" function
• Landing call button mounting frame
• Mounting frame for optional IP cameras
• Voice assistant mounting frame (Amazon Alexa)
• Device with multi-lingual support
• On-case touch button for preview; on-case touch
button for lock; 4 on-case status icons (messages,
Wi-Fi disconnected; lock activated; Do Not Disturb
function "DND"). Backlit buttons and icons
Technical data:
• DC input: 32V via system bus (use the power supply unit
provided in the kit)
• 7" LCD TFT screen
• 1024 x 600 LCD resolution (RGB)
• Micro SD card slot: SDHC format, - Memory size 8 – 128
GB, Speed class: Class4 - Class10
• Internal flash memory support for storing video, picture
and audio messages
• Dimensions (mm) 184 (L) x 146 (H) x 24 (D) (without
surface mounting bracket) 184 (L) x 146 (H) x 24 (D) (with
surface mounting bracket)
• IEEE 802.11 b/g/n 2.4GHz Wi-Fi – If the indoor station
is connected to the Wi-Fi, we recommend positioning
it where the
signal strength is at least -60 dBm
corresponding to two lines in Wi-Fi icon
• Frequency range: 2412-2472 MHz
• RF transmission power: < 100 mW (20 dBm)
• Surface mount installation.
• Can be installed with flush mounting boxes:
- Box 7249 (with bracket 40196)
- Circular box 2M V71701
- Box 3M V71703, V71303 horizontal/vertical
- British Standard square box
App
Functions
• A MyVimar account is needed to use the VIEW Door
App with IPo2W devices
• Available for both Android (Android 5.1 and later) and
iOS (iOS 9.0 and later) systems
• Support for audio/video calls from outdoor stations
• Preview of connected IP cameras
• Audio/video preview from outdoor stations
• Support for audio calls from and to indoor stations
• List of calls received function
• Image and/or video save function from calls or
consultation
• Multi-device management function
• Remote lock or relay activation
• Communication time setting from 60s to 300s
• Picture auto-rotate function
• Ability to set HD image quality: HD - SD - LD
• Zoom function support
Package contents
Indoor Station:
The indoor station is accompanied by:
• 1 (one) plastic bah with 1 (one) 6-pin terminal; 2 (two) two-
wired wirings; 1 (one) 12-cable wiring; 4 (four) plastic wall
plugs;
• 4 (four) metal screws; wall mounting bracket.
(The indoor station is wrapped in a protective plastic bag)
EN
3
