Intended Use; Before Using The Appliance For The First Time - Ritter markant 01 Instrucciones De Uso

English
Unfold the illustrations at the front
and back of this manual.
Please read these instructions
thoroughly before you start to use
the appliance. Keep these operat-
ing instructions in a safe place
and ensure that they are included
with the appliance if passing it on
to a third party.
Alternatively, the current operat-
ing instructions are available at
www.ritterwerk.de.

INTENDED USE

The food slicer is used to slice
household foods.
If the appliance is used for a
purpose other than this, or if it is
operated incorrectly, severe inju-
ries may occur or the appliance
may be damaged. All warranty
and liability claims will be ren-
dered null and void in this case.
BEFORE USING THE
APPLIANCE FOR THE
FIRST TIME
Preparation
Remove the appliance carefully
from the packaging. Remove all
packaging parts and keep these
together with the packaging in a
safe place. Clean the appli-
ance before allowing it to come
into contact with any food (see
CLEANING).
Setting up the appliance
• Set the appliance down on a
flat, non-skid surface close to a
mains socket.
On the positioning plate (6)
remove the left-over holder (8),
the finger protection (7a) and the
slide unit (7b) one after the other
by pulling them out and up.
Mounting the slice car-
riage (7): Insert the finger protec-
tion into the slot in the base of
the carriage and fasten it in place
by sliding it in the direction of the
arrow.
10
Unwind the power cord (11)
to the length required from the
cable compartment (4) under the
appliance. In doing so, fasten the
power cord in the slot provided for
it on the base of the appliance.
Swivel the positioning plate
fully downwards into the working
position.
Place the slice carriage's
guide runner onto the positioning
plate's lateral guide groove at an
incline. Swivel the slice carriage
downwards in the direction of
the positioning plate. The slice
carriage's guide runner must be
fully mounted onto the positioning
plate's guide groove.
Slide the left-over holder (8)
onto the finger protection (7a).
• Plug the cable into the socket.
SLICING
Use the slice thickness adjust-
ment knob (2) to set the required
thickness.
Place the food to be sliced
onto the slice carriage (7). Use
the left-over holder (8) to press it
up against the stop plate (3).
Protect your hands, by always
using the slice carriage and,
where applicable, the left-over
holder. Exception: Excessively
large foods to be sliced.
Turn the appliance on using
the power switch (1). Two operat-
ing modes are available:
Temporary operation: Press the
power switch and slide it towards
the arrow until you feel some
resistance. The rotary blade (10)
runs as long as the power switch
is pressed and held down in this
position.
Continuous operation: Press
the power switch and slide it
towards the arrow beyond the
resistance point until it latches
into place. The rotary blade runs
without the power switch having
to be pressed and held down,
until you push the power switch
back into the "0" position.
Note:
Never use the appliance for more
than a maximum of 5 minutes in
continuous operation.
For markant /orbis model
Adapt the slicing speed using the
electronic rpm adjustment (12) to
suit the food to be sliced. When
slicing soft food, set a low slicing
speed. Set a higher speed for
hard food.
• With the appliance running,
gently feed the food to be sliced
into the path of the rotary blade.
• When finished slicing, wait until
the rotary blade has come to a
complete stop.
• After each use, turn the slice
thickness adjustment knob to the
"0" position, in order to cover up
the sharp rotating blade and to
avoid any injuries.
CLEANING
Caution:
Switch the appliance off before
cleaning it; pull the power plug
out of the socket and turn the
slice thickness adjustment
knob (2) to the "0" position.
Clean the food slicer regularly
to prevent the accumulation of
food residue. The rotary blade
must also be cleaned regularly
as described below to prevent its
surface from rusting.
Note:
Over time, an accumulation of
food residue may cause damage
to the surface of the rotary blade,
causing it to rust.
:
05