Idiomas disponibles
Idiomas disponibles
OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the instruction book
carefully.
CHARGING
A) BATTERY CHARGING
The battery charger supplied is matched to the Li-ion battery
installed in the machine. Do not use another battery charger.
The Li-ion battery is protected against deep discharging. When
the battery is empty, the machine is switched off by means of a
protective circuit: The tool holder no longer rotates.
In a warm environment or after heavy use, the battery pack may
become too hot to permit charging. Allow time for the battery to cool
down before recharging.
When the battery is charged for the first time and after prolonged
storage, the battery will only accept approximately 60% charge.
However, after several charge and discharge cycles the battery will
accept a 100% charge.
B) TO REMOVE OR INSTALL BATTERY PACK (SEE
FIG. A1)
Depress the Battery Pack Release Button to release and slide the
Battery Pack out from your tool. After recharge, Slide it back into
your tool. A simple push and slight pressure will be sufficient.
C) CHARGING PROCEDURE(SEE FIG. A2)
NOTE:
a) Do not use any charger other than that specifically provided for
use with the equipment.
b) If the battery pack is very hot you must remove your battery
pack from the charger and allow time for the battery to cool
down before recharging.
c) The battery in your new tool is not charged when it leaves the
plant. Therefore it must be full charged before using the first
time.
d) Please charge the battery to reach full or no less than half
charge before storage. If the tool will not be used for long
periods of time, charge the battery every 3-6 months.
1) Plug the charger into an appropriate outlet.
2) Place the battery pack into the charger.
3) When charging is completed, unplug the charger and remove
the battery pack.
WARNING: When battery charge runs out after
continuous use or exposure to direct sunlight or heat, allow
time for the battery to cool down before recharging to achieve the
full charge.
CHARGING INDICATOR
Light
On/Off
Red on
Green on
OPERATION
1. ON / OFF SWITCH (SEE FIG. B)
Depress the On/Off switch to start and release it to stop your drill.
The on/off switch is fitted with a brake function which stops your
EN
chuck immediately when you quickly release the switch.
It is also a variable speed switch that delivers higher speed and
torque with increased trigger pressure. Speed is controlled by the
amount of switch trigger depression.
produced internally.
motor overheating.
2. SWITCH LOCK (SEE FIG. C1)
The switch trigger can be locked in the OFF position. This helps to
reduce the possibility of accidental starting when not in use. To lock
the switch trigger, push the rotation control in the center position.
3. FORWARD AND REVERSE ROTATION CONTROL
(SEE FIG. C2, C3)
Forward rotating: push the forward/reverse rotation control to the
left (the drill points away from you). It is used for drilling and screw
driving.
Reverse rotation: push the forward/reverse rotation control to the
right (the drill points away from you). It is used for remove screws or
release a jammed drill bit.
until it has stopped!
4. TWO-SPEED GEAR CONTROL (SEE FIG. D)
The drill has a two-speed gear control designed for drilling or driving
at LO (mark is 1) or HI (mark is 2) speeds. A slide switch is located
on top of the drill to select either LO or HI speed. When using the
drill in the LO speed range, the speed will decrease and the drill will
have greater power and torque. When using the drill in the HI speed
range, the speed will increase and the drill will have less power and
torque.
GEAR I
Low speed range: for screwdriving or working with large drilling
diameter.
GEAR II
High speed range: for working with small drilling diameter.
before changing the direction of rotation or the
two-speed gear control.
5. CHUCK ADJUSTMENT (SEE FIG. E)
To open the chuck jaws rotate the front section of the chuck. Insert
Status
the drill bit between the chuck jaws and rotate the front section
in the opposite direction. Ensure the drill bit is in the center of the
Charging
chuck jaws. Finally, firmly rotate the front chuck section in the
opposite directions. Your drill bit is now clamped in the chuck.
Fully charged
6. TORQUE ADJUSTMENT (SEE FIG. F)
The torque settings are controlled and adjusted by the torque
setting collar, but only affects the output when the screwdriving
function is selected.
The drilling function (Fig. G1), screwdriving function (Fig. G2) and
the hammer function (Fig. G3) are all selected by using the function
selection collar.
WARNING: Do not operate for long periods
at low speed because excess heat will be
WARNING: When overload occurs, release
the On/Off switch immediately to avoid the
WARNING: Never change the direction of
rotation when the chuck is rotating, wait
WARNING: To prevent gear damage, always
allow the chuck to come to a complete stop
WARNING: When overload occurs frequently
on the high speed gear, switch to the low
speed gear to avoid the motor overheating.
17
