Chicco baby hug 4in1 Manual De Instrucciones página 18

D - Tubular seat frame
E - Fabric (with shoulder straps)
F - Booster cushion
G - Toybar
G1 - Light / sound game buttons
G2 - 3 soft toys
I - Upper fabric zips
L - Plastic clips
M - Height adjustment pedal
N - Backrest recline lever
ASSEMBLY
The product is not assembled when purchased. To use
it, carry out the following assembly operations:
1. The first thing to do is assemble the "A1" wheels on
height adjustable base frame "A". To do this place the
frame on a rug or soft surface so as not to damage the
floor or frame. Assemble the 4 "A1" wheels inserting
the pins in the 4 holes under height adjustable base
frame "A" as shown in figure 1.
WARNING: Fully insert the wheel pin into the hole in
the base. At this point the base can be rested on the
floor.
2. Insert the fasteners of seat frame "B" into the respec-
tive tubes on seat structure "C" until they click into
place (Fig. 2).
3. Assemble the seat (seat frame "B" + seat structure
"C") on the base: insert the two tubes on base "A"
into the corresponding holes on seat frame "B" until
they click into place (Fig. 3).
WARNING: The backrest must face the height adjust-
ment pedal (I) as shown in Fig. 3a.
4. Insert tube "D" into the corresponding holes on seat
frame "B" until they click into place (Fig. 4).
5. To assemble fabric "E" line up the holes on the fabric
with the restraint system installed on seat structure
"C". Pass the two lateral arms of seat frame "B" through
the side fabric holes (FIG. 5), insert the pins of the
arms into the holes on either side of the backrest (FIG.
5a) until they click into place.
WARNING: Check that both arms are assembled cor-
rectly.
6. Attach fabric "E" using the two perimeter zips above
seat frame "B" (Fig. 6).
7. Pass the crotch strap and waist straps on seat struc-
ture "C" through the holes of fabric "E" (Fig. 7-7a-7b-
7c).
8. Attach the fabric (E) to the bottom of seat structure
"C", making sure to insert all of the plastic clips in the
right slots (Fig. 8-8a).
9. Press down on the lower part of the seat frame "C"
until it locks to the tube on the frame "A" (Fig. 9-9A).
10. Insert the central support "A2" under the joint of the
frame "A" (Fig. 10a-10b). Be sure that the product is
not at its maximum height when carrying out this
operation.
BOOSTER CUSHION
11. Reducer cushion "F" is ideal from birth and can be
used or removed as necessary. To attach it to the
seat, place it on the fabric, pass the crotch strap and
waste straps through the holes in booster cushion
"F" (reclined cradle mode), (Fig. 11). In high chair
mode it is also necessary to pass the shoulder straps
through the holes of the booster cushion (Fig. 11a).
TOYBAR
12. The toys can be attached to the toybar by passing the
straps through the plastic openings on the bar (Fig.
12) and fastening the velcro.
13. Assemble the toybar (with the light positioned to-
wards backrest recline lever "N") inserting the pins of
the bar into the holes on seat frame "B" until it clicks
into place (Fig. 13).
14. To incline the toybar in the three possible positions
press the side buttons (Fig. 14).
15. To remove the toybar press the buttons on the inside
of the bar support and pull upwards (Fig. 15).
WARNING: This toy must be assembled by adults only.
WARNING: Always check that the toybar is properly
fastened before using it.
WARNING: To prevent possible injury by entaglement,
remove this toy when the child starts trying to get up
on its hands and knees in a crowling position.
HEIGHT ADJUSTMENT
16. Once assembled, the product can be adjusted to
various heights in all configurations. To adjust its
height, hold down height adjustment pedal "M" (Fig.
16) and lift or lower the seat to the desired height.
ADJUSTING THE BACKREST
17. The backrest can be adjusted to four different posi-
tions. To do this, push down on backrest recline lever
"N" (Fig. 17).
Position 1 – Crib mode (Fig. 17a)
Position 2-3 – Reclined cradle mode (Fig. 17b)
Position 4 – High chair and first chair at the table mode
(Fig. 17c)
These adjustments can also be made with your child
seated in the product. In this case it will be slightly more
difficult.
WARNING: Always check that the backrest is properly
locked before use.
USING THE SAFETY HARNESS
18. With fabric "E" assembled on seat structure "B", there
will be a crotch strap, two waist straps and two
shoulder straps (Fig. 18).
19. CRIB MODE - WARNING: Completely remove all
safety harnesses making sure to keep them out of
the reach of your child (Fig. 19).
20. RECLINED CRADLE MODE - WARNING: A 3-point
restraint system must be used: crotch strap + waist
straps (Fig. 20).
21. After placing your child in the seat, reclined cradle
mode, fasten the straps by passing the two prongs
through the crotch strap buckle; adjust the waist
straps so that they fit closely around your child's
waist (Fig. 21).
18