Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

OPERATION AND MAINTENANCE MANUAL FOR
SERIES 9RS, 9S AND 9T ANGLE WRENCHES
Series 9RS, 9S and 9T Angle Wrenches are designed for heavy–duty close–quarter threaded
fastener applications which require precise torque repeatability.
Ingersoll–Rand is not responsible for customer modification of tools for applications on which
Ingersoll–Rand was not consulted.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code for Portable Air Tools
(ANSI B186.1).
For safety, top performance, and maximum durability
of parts, operate this tool at 90 psig (6.2 bar/620 kPa)
maximum air pressure at the inlet with 1/2" (13 mm)
inside diameter air supply hose.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
Do not use damaged, frayed or deteriorated air hoses
and fittings.
Be sure all hoses and fittings are the correct size and
are tightly secured. See Dwg. TPD905–1 for a typical
piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating this
tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 1999
Printed in U.S.A.
TPD1392
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
03539616
Keep hands, loose clothing and long hair away from
rotating end of tool.
Note the position of the reversing lever before
operating the tool so as to be aware of the direction of
rotation when operating the throttle.
Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Tool accessories may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool
if discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
Use only impact sockets and accessories. Do not use
hand (chrome) sockets or accessories.
The Throttle Valve Cap is under pressure from the
Throttle Valve Spring. Use care when removing the
Throttle Valve Cap. (On tools where applicable.)
Whenever the Angle Head is installed or repositioned,
the Throttle Lever must be positioned so that reaction
torque will not tend to retain the throttle in the "ON"
position.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
F
Form P7085
Edition 5
E
September, 1999
P
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 9RS Serie

  • Página 7: Uso De La Herramienta

    MANUAL DE USO Y MANTENIMIENTO PARA LLAVES ANGULARES MODELOS 9RS, 9S Y 9T NOTA Las Llaves Angulares Modelos 9RS, 9S y 9T están diseñadas para trabajo pesado en aplicaciones de abrazadera roscada de distancia mínima que requieran repetibilidad de par precisa.
  • Página 8: Etiquetas De Aviso

    ETIQUETAS DE AVISO AVISO EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRÍA OCASIONAR LESIONES. ADVERTENCIA ADVERTENCIA ADVERTENCIA Cortar siempre el suministro de aire y desconectar la man- Use siempre protección ocular Use siempre protección para guera de suministro de aire cuando utilice esta herramienta los oídos cuando utilice esta antes de instalar, retirar o ajus-...
  • Página 9: Especificaciones

    PARA PONER LA HERRAMIENTA EN SERVICIO ESPECIFICACIONES Modelo Dispositivo de Gama de Par Velocidad Cuadradillo (Retirada Suave) Libre 50 psi 90 psi pulg. ft–lbs (Nm) ft–lbs (Nm) 9RSM53 calado 25,0 (33,9) 40,0 (54,2) 9RSN53 calado 32,0 (43,4) 50,0 (67,8) 9RSP53 calado 39,0 (52,9) 58,0 (78,6)
  • Página 12: Especificações

    COLOCANDO A FERRAMENTA EM FUNCIONAMENTO ESPECIFICAÇÕES Modelo Equipamento Intervalo de Torque Velocidade Encabadouro (Apertos Ligeiros) Livre Quadrado de Torque 50 psi 90 psi pol. Nm (pés–lb) Nm (pés–lb) 9RSM53 paragem 33,9 (25,0) 54,2 (40,0) 9RSN53 paragem 43,4 (32,0) 67,8 (50,0) 9RSP53 paragem 52,9 (39,0)
  • Página 13: Maintenance Section

    MAINTENANCE SECTION 9T WITH AUTOMATIC SHUTOFF (Dwg. TPB963)

Tabla de contenido