Wall Mounting; Optional Accessory - DeWalt DCD703 Manual De Instrucciones

may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

Some D WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Belt Hook (Fig. A)

Optional Accessory


WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
IMpoRTaNT: When attaching or replacing the belt hook,
use only the screw that is provided. Be sure to securely
14
tighten the screw.
The belt hook 13 can be be attached to either side of the
tool using only the screw provided, to accommodate left- or
right- handed users. If the hook is not desired at all, it can be
removed from the tool.
To move belt hook, remove the screw that holds the belt
hook in place then reassemble on the opposite side. Be sure
to securely tighten the screw.
Installing and Removing Attachments
(Fig. A, E)

WARNING: Burn hazard. Moving parts within the
power unit become hot during use. Avoid contact with
moving parts within power unit when removing and
installing accessories.

WARNING: Before assembly, lock the power unit by
setting the forward/reverse slider
position and remove the battery from the tool. Remove
4 to the center
any accessory from the attachment before removing or
installing the attachment.

WARNING: Only use attachments that are specifically
designed for and compatible with the power unit.
1. Pull back on the locking sleeve
the direction of the arrow.
2. Slide the attachment onto the spindle
detents on the attachment with the lugs
18
the spindle. You may have to rotate the attachment
slightly to align the spindle with the mating shaft of
the attachment.
NoTE: Once on the spindle you may have to rotate the
attachment a small bit side to side so the detents align
with the lugs. The 3/8" chuck attachment
have any detents to align.
3. To remove the attachment, pull back on the locking
sleeve in the direction of the arrow and remove the
attachment from the spindle.
NoTE: The 1/4" hex right angle attachment
additional attchments to be installed on its spindle. With
the 1/4" hex right angle attachment installed on the
tool follow instruction 1 and 2 of this section to install
additional attachments.
NoTE: The locking sleeve
will rotate along with the chuck while the tool is operating,
while the sleeves of the other attachments do not.
Installing a Bit or Accessory into a Keyless
Chuck (Fig. A, F)

WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changing acces sories.

WARNING: Always ensure the bit is secure before
starting the tool. A loose bit may eject from tool
causing possible personal injury.
The 3/8" chuck attachment
To insert a drill bit or other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the
chuck 22 and tighten securely by grasping and rotating
the chuck sleeve 12
holding the tool with the other. When the chuck is
nearly tightened you will hear a clicking sound. After
12-14 clicks the chuck is securely tightened around
the accessory. Your tool is equipped with an automatic
spindle lock mechanism. This allows you to open and
close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
16 on the attachment in
, aligning the
17
19
does not
8
allows
9
16 of the 3/8" chuck attachment
8 uses a keyless chuck.
of the chuck with one hand
12
clockwise with one hand while
ENGlIsH
around
29