HIKVISION DS-2XC6626G0/P-IZHS Guia De Inicio Rapido página 7

which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a
designated collection point.For more information
see: www.recyclethis.info.
Safety Instruction
These instructions are intended to ensure that the
user can use the product correctly to avoid danger
or property loss.
Laws and Regulations
The device should be used in compliance with local
laws, electrical safety regulations, and fire
prevention regulations.
Electricity
In the use of the product, you must be in strict
compliance with the electrical safety regulations of
the nation and region. The equipment shall not be
exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be
placed on the equipment. Provide a surge
suppressor at the inlet opening of the equipment
under special conditions such as the mountain top,
iron tower, and forest. CAUTION: To reduce the risk
of fire, replace only with the same type and rating
of fuse.
Battery
For the device without the supplied battery, use the
battery provided by qualified manufacturer. Refer
to the product specification for detailed battery
requirements.
Do not ingest battery. Chemical burn hazard! This
product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead to
death. Keep new and used batteries away from
children. If the battery compartment does not close
securely, stop using the product and keep it away
from children. If you think batteries might have
been swallowed or placed inside any part of the
body, seek immediate medical attention. CAUTION:
Risk of explosion if the battery is replaced by an
incorrect type. Dispose of used batteries according
to the instructions. Improper replacement of the
battery with an incorrect type may defeat a
safeguard (for example, in the case of some lithium
battery types). Do not dispose of the battery into
fire or a hot oven, or mechanically crush or cut the
battery, which may result in an explosion. Do not
leave the battery in an extremely high temperature
surrounding environment, which may result in an
explosion or the leakage of flammable liquid or gas.
Do not subject the battery to extremely low air
pressure, which may result in an explosion or the
leakage of flammable liquid or gas. + identifies the
positive terminal(s) of equipment which is used
with, or generates direct current. - identifies the
negative terminal(s) of equipment which is used
with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles,
should be placed on the equipment. The serial port
of the equipment is used for debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned fingers when handling
can be hot and should not be touched without
taking care. For device with this sticker, this device
is intended for installation in a restricted access
location, access can only be gained by service
persons or by users who have been instructed
about the reasons for the restrictions applied to the
location and about any precautions that shall be
taken.
Installation
Install the equipment according to the instructions
in this manual.
Power Supply
Device powered by Safety Extra-Low Voltage(SELV):
The power source should meet limited power
source or PS2 requirements according to IEC
60950-1 or IEC 62368-1 standard.
Device powered by AC mains supply voltage: The
equipment must be connected to an earthed mains
socket-outlet. An appropriate readily accessible
disconnect device shall be incorporated external to
the equipment. An appropriate overcurrent
protective device shall be incorporated external to
the equipment, not exceeding the specification of
the building. An all-pole mains switch shall be
incorporated in the electrical installation of the
building. Ensure correct wiring of the terminals for
connection to an AC mains supply. The equipment
has been designed, when required, modified for
connection to an IT power distribution system.
For the device without the supplied power adapter,
use the power adapter provided by qualified
manufacturer. Refer to the product specification for
detailed battery requirements.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from
this product. DO NOT stare at operating light source.
May be harmful to the eyes. Wear appropriate eye
protection or DO NOT turn on the white light when
you assemble, install or maintain the camera.
Transportation
Keep the device in original or similar packaging
while transporting it.
System Security
The installer and user are responsible for password
and security configuration.
Maintenance
If the product does not work properly, please
contact your dealer or the nearest service center.
We shall not assume any responsibility for
problems caused by unauthorized repair or
maintenance. A few device components (e.g.,
electrolytic capacitor) require regular replacement.
The average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside
and outside surfaces of the product cover. Do not
use alkaline detergents.
Using Environment
DO NOT place the camera in extremely hot, cold,
6
the parts. Wait one-half hour
after switching off before
handling parts. This sticker is to
indicate that the marked item