Technical Specifications - Rupes LHR12E Traducción Del Manual De Instrucciones Original

TECHNICAL SPECIFICATIONS

TYPE
Ø POLISHING FOAM mm
Ø BACKING PAD mm
Ø ORBIT mm
POWER
R.P .M.
WEIGHT
ELECTRONIC SPEED CONTROL
INSULATION CLASS
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary. Refer to the label technical
PICTOGRAPH
product.
Important safety indications
Use personal
protective equipment.
Double insulated tool.
INSULATION CLASS II
CE compliant
WARNINGS
The safety and accident prevention instructions are reported
in the "SAFETY INSTRUCTION" booklet which is an integral
part of these documents. This operating instructions manual
use of the tool.
CORRECT USAGE
This tool is designed to e used as a polisher. Read all the
warnings, instructions, indications provided on drawings
and speci cations supplied with this tool. Failure to comply
with all the instructions provided below may cause electrical
This tool is not intended to e used for smoothing, metal
rushing and cutting operations. The use of this tool for
people.
The tool must e used with accessories that have een
speci call designed or recommended
safe operation.
The rated speed of the accessories must
e uivalent to the ma imum speed speci ed on the tool.
Using the accessories at speeds above the rated one, may
The e ternal diameter and thickness of the accessories
must match the speci cations of the tool. Accessories
with incorrect dimensions cannot be adequately protected or
controlled.
The con guration of accessories must match the tool.
impossibility of controlling the tool.
Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verif
there are no cracks, tears or e cessive wear. If the tool or
accessor has fallen, verif that it is not damaged or install
a new accessor . After inspecting or installing an accessor ,
test the operation of the tool at ma imum speed and without
load for one minute, keeping at a safet distance. If the
accessories are damaged, they will break during this test.
SPECIFIC SAFETY WARNINGS
Verif that no loosened part of the polishing tool shroud or
the locking ties can rotate freel . Safel position or cut all
the loosened
ma twist around the operator's ngers or get caught
work piece eing machined.
STARTING UP
TOOL ASSEMBLY
Position the cap (5) on the gearbox such that the holes for
mounting the screws (7) are aligned with those on the gearbox.
ACCESSORIES ASSEMBLY
BACKING PAD
1. Place the disc pad (8) in the centre;
3.
pad Allen wrench (10). Do not tighten the disc pad if it is in
POLISHING FOAM
Apply pressure on polishing pad to join pad to plate.
START AND STOPPING
- Handhold: hold with both the hands, one on the head and the
the manufacturer.
POLISHING FOAM
Apply pressure on polishing pad to join pad to plate.
e at least
START AND STOPPING
- Handhold: hold with both the hands, one on the head and the
other one on the bottom of the tool housing. This is the only
right grip.
- Starting: push the lever of the switch (2) handle.
- Stopping: push and release the lever (2) of the switch.
SELECTING RPM
The rpm can be adjusted by rotating the wheel (3). The choice
of speed depends on the characteristics of the abrasive disc
and the material to be worked.
LHR 12E
130-150
125
12
400
4000÷5500
2,3
•
II
ing wires. Loosened or revolving
Voltage and power frequency must match the data
tool is switched off before plug is connected.
th th b tt
The tool continues to rotate after it is turned off.
Do not run to "empty" the tool with the polishing pad
mounted. In this way, the polishing pad may be subject
to lacerations
ENGLISH
LHR 75E
80-100
75
12
400
4000÷5500
2
•
II
f th t l h i Thi i th
6
ing wires
the
l