SNOWJOE 24V-X4-SB24-CT Manual Del Operador página 14

4. Note the wind direction. If possible, move in the same
direction as the wind so that the snow is not thrown
against the wind (and thus back into your face and on the
just cleared path).
5. Do not push the snow blower with excessive force. Do not
exceed the unit's intake or throw rate.
6. Some parts of the snow blower may freeze under extreme
temperature conditions. Do not attempt to operate the
snow blower with frozen parts. If the parts freeze while
the snow blower is in use, stop the snow blower, remove
the batteries, and inspect for frozen parts. Free all parts
before restarting or operating the snow blower. Never
force controls that have frozen.
Maintenance
To order genuine replacement parts or accessories for the
Snow Joe 24V‑X4‑SB24‑CT Cordless Snow Blower, please
®
visit snowjoe.com or contact the Snow Joe
customer service center at 1‑866‑SNOWJOE
(1‑866‑766‑9563).
m
WARNING!
Make sure to turn off the snow blower and
remove the batteries before performing any maintenance task
on your snow blower.
General Maintenance Tips
1. Do not attempt to repair the machine unless you have the
proper tools and instructions for disassembly and repair of
the machine.
2. Check bolts and screws at frequent intervals for proper
tightness to ensure that the equipment is in safe
working condition.
3. After each snow removal session, run the snow blower
for a few minutes to prevent the collector/impeller from
freezing. Shut off the motor, wait for all revolving parts to
stop completely, remove the batteries and wipe residual
ice and snow off the unit.
Proper Care for Batteries + Chargers
m
WARNING!
To reduce the risk of injury, always unplug
the chargers and remove the battery packs from the chargers
before performing any maintenance task. Never disassemble
the battery packs or chargers. Contact your Snow Joe
Sun Joe dealer or the Snow Joe
®
service center for ALL repairs.
1. To reduce the risk of injury and damage, never immerse
your battery packs or chargers in liquid or allow any liquid
to flow inside these components.
2. Clean out dust and debris from charger vents and
electrical contacts by blowing with compressed air.
+ Sun Joe
® ®
+
®
+ Sun Joe customer
® ®
3. Use only mild soap on a damp cloth to clean the battery
packs and chargers, keeping away from all electrical
contacts. Certain cleaning agents and solvents are
harmful to plastics and other insulated parts. Some of
these include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never use
flammable or combustible solvents around battery packs,
battery chargers or tools.
4. The 24V iON+ lithium‑ion battery chargers have no
serviceable parts.
Check Tire Pressure
m
WARNING!
Under any circumstance do not exceed
manufacturer's recommended PSI. Equal tire pressure
should be maintained at all times for performance purposes.
Excessive pressure may cause tire/rim assembly to burst with
force sufficient to cause serious injury. Refer to sidewall of tire
for recommended pressure.
The tires are over‑inflated for shipping purposes. Check the
tire pressure before operating the snow blower and deflate (or
inflate) the tires as necessary.
Manufacturer's
Recommended
Tire Pressure
m
CAUTION!
Avoid injury. Explosive separation of tire and
rim parts is possible when they are serviced incorrectly:
• Do not attempt to mount a tire without proper equipment
and experience to perform the job.
• Do not inflate the tires above the recommended pressure.
• Do not weld or heat a wheel and tire assembly. Heat can
cause an increase in air pressure resulting in an explosion.
Welding can structurally weaken or deform the wheel.
• Do not stand in front or over the tire assembly when
inflating. Use a clip‑on chuck and extension hose long
enough to allow you to stand to one side.
Replacing Skid Shoes
The skid shoes on the bottom of the snow blower are subject
to wear. They should be checked periodically and replaced
when necessary.
To replace skid shoes:
1. Position unit on a hard, flat, smooth level surface.
2. Using the 13 mm open end wrench, remove the 4 hex
nuts (2 on each side), washers and bolts which secure the
skid shoes to the snow blower (Fig. 26).
14
20 PSI