EINHELL TE-CS 18/165 Li Manual De Instrucciones página 14

•
Refasten the locking screw for miter setting
(7). Check that everything is securely
fastened.
5.3 Extraction of dust and chips (Fig. 6)
•
Connect a suitable vacuum cleaner (b) to
the provided sawdust extractor connection
(14) of your circular saw (vacuum cleaner
not included). This will ensure optimum dust
extraction from the workpiece. The benefits
are that you will protect both the equipment
and your own health. Your work area will also
be cleaner and safer.
•
Dust created when working may be
dangerous. Refer to the section entitled
"Safety instructions".
•
Important! The vacuum cleaner you use for
the vacuum extraction must be suitable for
the material you are cutting.
•
Check that all parts are properly joined
together.
5.4 Edge guide (Figure 7/8)
•
The edge guide (16) enables you to saw
parallel lines.
•
Slacken the locking screw for the edge guide
(8) on the saw foot (6).
•
To assemble, slide the edge guide (16) into
the guide (c) on the saw foot (6) (see Fig. 7).
•
Set the required distance and then tighten the
locking screw (8) again.
•
Using the edge guide: Position the edge
guide (16) flat on the edge of the workpiece
and start the sawing.
Important! Carry out a trial cut in a piece of
waste wood.
5.5 Line guide (Fig. 9)
Using the line guide (15) you can carry out
exact cuts following cutting lines marked on the
workpiece. Use the mark (d) for the 0° or 90°angle
setting and the mark (e) for the 45° angle setting.
For information on the angle setting see 5.2
Important! Carry out a trial cut in a piece of
waste wood.
6. Operation
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Anl_TE_CS_18_165_Li_USA_SPK7.indb 14 Anl_TE_CS_18_165_Li_USA_SPK7.indb 14
EN
6.1 Working with the cordless circular saw
•
Always hold the tool firmly by the handles
provided (1 and 10) to ensure that you handle
it safely when using it.
•
The swing guard hood (19) is pushed back
automatically by the workpiece.
•
Do not use force! Push forward gently and
evenly with the circular saw.
•
The waste piece should be on the right-hand
side of the circular saw so that the wide
section of the support bench supports its full
area.
•
If you are sawing down a line that has been
drawn, guide the circular saw along the
corresponding notch.
•
Clamp small pieces of wood securely before
sawing them. Never hold them with your
hand.
•
Always follow the safety instructions. Wear
safety goggles.
•
Do not use defective saw blades or blades
that are cracked or broken.
•
Do not use any flanges / flange nuts whose
bore hole is larger or smaller than those in the
saw blade.
•
The saw blade must not be decelerated by
hand or by applying lateral pressure to the
blade.
•
Check that the swing guard hood works
properly. The swing guard hood must not jam,
and it must return to its initial position when
you have completed the cut.
•
Before you use the circular saw, check the
function of the swing guard hood with the
battery disconnected.
•
Before you use the machine, make sure that
the safety equipment such as the swing guard
hood, flanges and adjustment devices are in
working order and are correctly adjusted and
secured.
•
You can connect a suitable dust extraction
system to the sawdust extraction connector
(14). Make sure that the dust extraction
system is safely and correctly connected.
•
The moving swing guard hood must not be
fixed in the retracted guard hood when the
saw is in use.
6.2 Using the cordless circular saw
•
Adjust the cutting depth, cutting angle and
parallel stop (see section 5.1, 5.2 and 5.4).
•
Do not switch on the circular saw until you
have fitted a saw blade.
•
Place the saw foot flat on the workpiece you
want to saw. The saw blade must not be in
- 14 -
04.05.2022 08:53:19 04.05.2022 08:53:19