Switch Action; Adjusting Depth Of Cut; Bevel Cutting - Makita HS004G Manual De Instrucciones

Ocultar thumbs Ver también para HS004G:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 84
Indicating the remaining battery capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
► Fig.8: 1. Indicator lamps 2. Check button
Indicator lamps
Lighted
Off
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when
the battery protection system works.

Switch action

WARNING:
Before installing the battery cartridge into
the tool, always check to see that the switch trigger actuates
properly and returns to the "OFF" position when released.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means. A switch with
a negated lock-off button may result in unintentional
operation and serious personal injury.
WARNING:
NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the lock-off
button. A switch in need of repair may result in unintentional
operation and serious personal injury. Return tool to a Makita
service center for proper repairs BEFORE further usage.
To prevent the switch trigger from being accidentally pulled, a lock-
off button is provided. To start the tool, depress the lock-off button
and pull the switch trigger. Release the switch trigger to stop.
► Fig.9: 1. Switch trigger 2. Lock-off button
NOTICE:
Do not pull the switch trigger hard
without pressing in the lock-off button. This can
cause switch breakage.
CAUTION:
The tool starts to brake the circular saw
blade rotation immediately after you release the switch
trigger. Hold the tool firmly to respond the reaction of the
brake when releasing the switch trigger. Sudden reaction
can drop the tool off your hand and can cause a personal injury.
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
Automatic speed change function
This tool has "high speed mode" and "high torque mode".
The tool automatically changes the operation mode
depending on the work load. When the work load is low,
the tool will run in the "high speed mode" for quicker
cutting operation. When the work load is high, the tool
will run in the "high torque mode" for powerful cutting
operation.
► Fig.10: 1. Mode indicator
The mode indicator lights up in green when the tool is
running in "high torque mode".
If the tool is operated with excessive load, the mode
indicator will blink in green. The mode indicator stops
blinking and then lights up or turns off if you reduce the
load on the tool.
Mode indicator status
On

Adjusting depth of cut

CAUTION:
After adjusting the depth of cut,
always tighten the lever securely.
Loosen the lever on the depth guide and move the base up or down.
At the desired depth of cut, secure the base by tightening the lever.
For cleaner, safer cuts, set cut depth so that no more
than one blade tooth projects below workpiece. Using
proper cut depth helps to reduce potential for danger-
ous KICKBACKS which can cause personal injury.
► Fig.11: 1. Lever

Bevel cutting

CAUTION:
After adjusting the bevel angle,
always tighten the clamping screws securely.
Loosen the clamping screws. Set for the desired angle by
tilting accordingly, then tighten the clamping screws securely.
► Fig.12: 1. Clamping screw
Use the stopper when you do precise 45° angle cutting.
Fully turn the stopper as illustrated depending on 0° -
45° bevel cut or 0° - 48° bevel cut.
► Fig.13: 1. Stopper
Sighting
For straight cuts, align the 0° position on the front of the
base with your cutting line. For 45° bevel cuts, align the
45° position with it.
► Fig.14: 1. Cutting line (0° position) 2. Cutting line
(45° position)
15 ENGLISH
Off
Blinking
High speed
High torque
Operation
mode
mode
mode
Overload
alert
Tabla de contenido
loading

Tabla de contenido