Elvox Petrarca Manual Para El Conexionado Y El Uso página 7

5) After 2 seconds the interphone emits a high tone and communica-
tion is enabled with the panel. If the monitor is also connected to the
interphone, it is switched on and connected to the camera of the
entrance panel.
6) Release the tab on the lock release pushbutton and the self start
pushbutton.
7) On pushbutton entrance panels, press the call button for the
"master" interphone (already programmed), while on alphanumeric
keypads, enter the call code of the "master" interphone and press
pushbutton " ".
8) When the secondary code is associated with the interphone and
communication is terminated.
Pushbutton programming
The interphone is supplied with a pair of additional pushbuttons type
692P, for the functions self start and the auxiliary service "stair light",
which activates the 1st relay of the 1st actuator (type 692R), if connec-
ted to the system. A further three pairs of pushbuttons type 692P can be
inserted in the interphone, to be connected to connectors T2-T3-T4, cor-
responding to the following default functions.
Pushbutton Connector Default function
1 T1 Self-start
2 T1 Stair light (1st relay of 1st actuator,
type 692R)
3 T2 Auxiliary (2nd relay of 1st actuator,
type 692R)
4° T2 Not associated
5° T3 Not associated
6° T3 Not associated
7° T4 Function F1 on panel
8° T4 Function F2 on panel
To change the operating mode of the 8 pushbuttons, use programmer
type 950C, with the exception of programming intercommunicating
pushbuttons and the pushbutton for the self-start service associated with
a specific panel.
If a pushbutton is programmed for a specific function, the interphone
emits a "Click" when pressed; otherwise it does not emit any signal.
Intercommunicating call pushbutton programming
Programming phase:
1) Raise the handset of the interphone or monitor to be called.
2) Remove the cover of the interphone to be programmed.
3) Press and hold the RESET pushbutton on the interphone.
4) Press and hold the additional pushbutton to make the intercommuni-
cating call together with the RESET pushbutton.
5) Release the RESET pushbutton, keeping the call pushbutton pres-
sed.
6) After 2 seconds the interphone emits a high tone, while the other
interphone emits a 3-tone ascending scale.
7) Release the intercommunicating call pushbutton.
8) On the interphone called (with the 3-tone ring), press one of the pro-
grammed pushbuttons (such as lock release, F1 or F2).
9) A high tone confirms the end of the procedure.
Repeat the same procedure for the other interphones and any other
intercommunicating call pushbuttons.
Programming the self-start pushbutton to a specific panel.
Programming phase:
1) Remove the interphone cover.
2) Press and hold the RESET pushbutton on the interphone.
3) Press and hold the additional pushbutton to activate the self-start
function together with the RESET pushbutton.
4) Release the RESET pushbutton, keeping the self-start pushbutton
pressed.
5) After 2 seconds the interphone emits a high tone.
6) Release the self-start pushbutton.
P R O G R A M M I N G / O P E R A T I N G
All manuals and user guides at all-guides.com
7) On pushbutton entrance panels, press the call button for the inter-
phone, while on alphanumeric keypads, enter the call code and
press pushbutton "
8) A high tone confirms the end of the procedure.
Restoring default values of pushbuttons.
Programming phase:
1) Remove the interphone cover.
2) Press and hold the RESET pushbutton on the interphone.
3) Press and hold the relative pushbutton to be reprogrammed together
with the RESET pushbutton.
4) Release the RESET pushbutton, keeping the other pushbutton pressed.
5) After 2 seconds the interphone emits a high tone.
6) Release the pushbutton to restore to default and then press again.
Deleting all settings.
Programming phase:
1) Remove the interphone cover.
2) Press and hold the RESET pushbutton on the interphone.
3) Press and hold the self start pushbutton together with the RESET
pushbutton.
4) Release the RESET pushbutton, keeping the self-start pushbutton
pressed.
5) After 2 seconds the interphone emits a continuous tone for two
seconds.
6) Release the self-start pushbutton.
7) During the continuous tone, press the tab on the lock release
pushbutton.
If the deletion procedure is successful, when the lock release tab is pres-
sed the interphone emits a triple "Beep".
OPERATION
Calls from an entrance panel, intercommunicating calls and door calls
are differentiated by means of different tones.
Door calls.
Calls from entrance panels do not follow the pressed pushbutton but are
generated inside the interphone. The call interval is 1 second of ringto-
ne and 2 seconds of pause repeated twice (default value set on panel).
To answer, raise the handset. If the handset is already raised during the
call, replace and raise it again. The call answer time (30 s) and the con-
versation time (2 minutes by default) are set in the panel parameters.
When the conversation time has elapsed, the user can continue without
replacing the handset if a new call is made within 10 seconds from the
same panel.
Intercommunicating call.
Lift the handset and press the intercommunicating button for the inter-
phone/monitor to be called. On the handset of the interphone called a
call tone will ring (if the call is enabled) or an engaged tone (if not ena-
bled). On the called interphone the ringtone starts sequentially at inter-
vals of 1 second ringing and 4 seconds pause. The maximum duration
of the call is 30 seconds (6 cycles). To answer the call, simply raise the
handset; the maximum duration of the conversation is 60 seconds.
When the conversation time has elapsed, the user can continue without
replacing the handset if a new call is made within 10 seconds. Calls from
the panel have priority over intercommunicating calls.
Denied calls.
Installation of type 6153/682 in the interphone, enables the user to vary
the call intensity or mute the ringtone. Call mute is indicated by perma-
nent illumination of the red LED. If calls are made to the interphone when
the call mute is enabled, they are denied. A denied call causes the red
Led to briefly switch off according to the number of times calls are denied
(maximum 4 denied calls). The signal is repeated every 10 seconds
(approx.). Deletion of denied calls is by: reenabling the ringtone, reset-
ting the interphone or a system power failure. On the panel, a denied call
is indicated by means of a dissuasion tone (a series of "Beeps" at 100ms
intervals with a pause of 100ms for a total of 5 seconds).
The message "Do not disturb" also appears on panels with display.
".
7