Important - BFT ZARA BTL2 Instrucciones De Instalación

1. Run the AUTOSET cycle (*)
2. Check the impact forces: if they fall within the limits (**) skip to point 9 of the
procedure, otherwise
3. Where necessary, adjust the sensitivity (force) parameter: see parameters table.
4. Check the impact forces again: if they fall within the limits (**) skip to point 9
of the procedure, otherwise
5. Apply a shock absorber profile
6. Check the impact forces again: if they fall within the limits (**) skip to point 9
of the procedure, otherwise
7. Apply pressure-sensitive or electro-sensitive protective devices (such as a
safety edge) (**)
8. Check the impact forces again: if they fall within the limits (**) skip to point 9
of the procedure, otherwise
9. Make sure all devices designed to detect obstacles within the system's operating
range are working properly
(*) Before running the autoset function, make sure you have performed all the
assembly and make-safe operations correctly, as set out in the installation
warnings in the drive's manual.
(**)Based on the risk analysis, you may find it necessary to apply sensitive protective
devices anyway
WARNING! Incorrect settings can result in damage to property and injury
to people and animals.
TABLE "A" - PARAMETERS
TRIMMER Parameter
Automatic
T1
closing time [s]
T2 Leaf force [%]
Slow-down
T3
distance [%]
Motor 1 closing
T4
delay time [s]
(*) In the European Union, apply standard EN 12453 for force limitations, and standard EN 12445 for measuring method.
TABLE "B" - LOGICS
DIP Logic
Transmitter
1
programming
2
BAR / 8K2
Photocell input
3
check
INSTALLATION MANUAL
+ +
min. max.
Waiting time before automatic closing.
0 120
NOTE: Set to 0 if not used.
Force exerted by leaf/leaves.This is the percentage of force delivered, beyond the force stored during the
autoset cycle (and subsequently updated), before an obstacle alarm is generated.
10 100
WARNING: It affects impact force directly: make sure that current safety requirements are met
with the set value (*). Install anti-crush safety devices where necessary.
Set slow-down speed as a percentage of total travel. This distance is travelled at low speed.
5 50
NOTE: When this parameter is edited, a new Autoset cycle must be run to confirm it.
Motor 1 closing delay time with respect to motor 2.
0 25
NOTE: set 0 for single motor operations (leaf 1).
Cross out
Default Description
setting used
Enables wireless memorizing of transmitters:
1- Press in sequence the hidden key and normal key (T1-T2-T3-T4) of a transmitter that has
already been memorized in standard mode via the radio menu.
2- Press within 10 sec. the hidden key and normal key (T1-T2-T3-T4) of a transmitter to be
ON memorized.
The receiver exits programming mode after 10 sec.: you can use this time to enter other new
transmitters.
ON
This mode does not require access to the control panel.
IMPORTANT: Enables the automatic addition of new transmitters, clones and replays.
Disables wireless memorizing of transmitters and automatic addition of clones.
Transmitters are memorized only using the relevant Radio menu or automatically with re-
OFF
plays.
IMPORTANT: Disables the automatic addition of new transmitters and clones
Input configured as Bar 8k2 (Fig.H, ref.5). Input for resistive edge 8K2.
ON
The command reverses movement for 2 sec.
OFF
Input configured as Bar, safety edge (Fig.H, ref.3-4).
OFF
The command reverses movement for 2 sec..
ON Enable safety check on the PHOT input
OFF
OFF Safety check on PHOT input not enabled
LED ERR:
Led SET
Lit
Reverse due to
obstacle - Ampe-
rostop
Unlit:
- Check for obsta-
cles in path
Internal system
supervision control
error.
- Try switching the
board off and back
Lit
on again.
If the problem
persists, contact
the technical
assistance de-
partment.
Photocell test failed
slow
- Check photocell
flashing
connection and/or
logic settings
Description
Led ERR
slow flashing fast flashing
Photocell test,
Costa o Costa 8k2 Thermal cutout
failed
- Check photocell - Allow automated
connection and/or device to cool
logic settings
Parameters
or Operating Logic
edited
- If the "Slow-down
distance" is edited,
run a new Autoset
cycle to confirm
the new setting.
- If other parame-
ters and/or opera-
ting logic are edi-
ted, hold down S2
for 5s to confirm.
NOTE: In any case,
the Autoset fun-
ction confirms all
changes made to
the board.
ZARA BTL2
and/
- 11