Parts; Technical Details; Safety Devices - CAMPAGNOLA Cobra Manual De Uso Y Mantenimiento

3 -SPECIFICATIONS

3.5 Parts

Pos. Description
1 Battery set
2 Braces buckles
3 Belt buckles
4 Battery backpack
5
Electronic system connector Connects the electronic card to the battery set
6 Cable loops
7 Battery charger plug
8 ON-OFF switch
9 Braces
10 Power supply cable
11 F
ront cover fixing screws
12 Trigger
13 ON–OFF led light
14 Cutting blade
15 Blade group
16 Anvil
17 Trigger guard
18 Electronic card box
19 Selector
20 Display
21
Electronic card power supply cable
22 Locking nut
23 Nut washer
24 Front cover fixing nuts Lock the blade replacement cover
25 Flared-headed screws Lock the anvil on the shear body
26 Cotter
27 Blade-drive gear
28 Pin washer
29 Blade pin
30 Front cover
31 Arm cable-fastener
32 Holster

3.6 Technical details

• Shear weight: ............................................................................ 940 gr
• Weight of battery, electronic card box and backpack: ...................... 3,8 kg
• Blade opening: .......................................................................... 35 mm
• Battery: .................................................................................... Li-FePo4
• Battery endurance: .................................................................... >10 ore
• Automatic electronic battery charger model ................................. 0136.0125 (max. recharging time: 5 hours)

3.7 Safety devices

• Built-in safety device: When not working, after 1 minute the trigger has to be pressed 3 times to re-start the
shear; after 5 minutes the electronic card has to be switched off and then on by means of the selector (19) to re-
start the shear; after 20 minutes the battery automatically disconnects from the power supply, so it has to be
started again by means of the switch (8).
• Inner protection device: Stops the tool due to inner overheating. It is indicated on the display by the flashing
word STOP followed by OVERLOAD.
• Heat-protection device: Stops the tool when the pre-set safety threshold has been reached, and allows to use it
again only when the temperature decreases by 5° C at least. It may take few minutes and is indicated on the
display by the flashing word STOP followed by MAX_TEMP.
• Battery self-stopping: Happens automatically after 20 minutes without working.
• ON-OFF led light (13): Indicates that the shear is working.
• Mechanic guard (17): Protects the trigger (12) from accidental operating.
• Arm cable-fastener: Keeps the cable close to the operator's arm so that he can move freely and the tool does
not get entangled in any object
40 - 112
Function
Operates the shear
Fasten the braces to the shoulders
Fasten the backpack
Allows to carry the battery set
Allow to fasten the cables to the backpack
Connects the charger to the battery set
Operates the electronic card
Hold 10% of the backpack weight
Connects the shear to the electronic card box
Fasten the cover for the blades replacement
Operates the shear
Indicates if the shear is on or off
Mobile blade
Cutting parts
Fixed blade
Protects the trigger from accidental operating
Contains the electronic card for operating the shear
Allows to select the shear operating mode
Shows the necessary information to operate the shear
Connects the electronic card to the battery set
Locks the blades pin
Distributes the nut pressure
Connects the blade to the blade-drive gear
Transmits motion to the cutting blade
Distributes the pin pressure on the blade-drive gear
Is the fulcrum of the cutting blade and the anvil
Allows to replace the blades
Keeps the cable close to the operator's arms, so that he can move freely
Protects the shear during the transport
Pict. No
A
A
A
A
A
A
A
A
A-F
B
B
B
B
B-E
B
B-E
B
C
C
C
C
D
D
D
D
D
D
D
D
D
E
E