Functional Principle; Product Information; Replacing The Battery - CYBEX SENSORSAFE Manual De Instrucciones

Registering several clips with one smartphone
You can register multiple clips to one smartphone and
EN
account and be connected to them simultaneously. To
do so, connect your smartphone with each clip one after
another by clicking "add new device" and following the
instructions.Leave all other clips in the area unbuckled
when registering a new clip for the first time.
Registering several smartphones with one clip
One clip can be registered with more than one
smartphone but only one smartphone can actively be
connected at a time. Please perform the registration
steps for one smartphone at a time. To switch between
connected users, the connected user must select
"Disconnect" in Settings to allow someone else to
connect.

FUNCTIONAL PRINCIPLE

After the SENSORSAFE clip has been installed on the
seat and connected to the App, it will communicate with
your smartphone when it is closed. The LED on the clip
will light up blue when it successfully connects to the the
SensorSafe mobile app on your smartphone. A red light
indicates that the clip is not connected to the App.
The following information will be sent to the application
by the closed clip, when connected via Bluetooth:
• status of the clip (open or closed)
• ambient temperature around the clip
• battery status
Furthermore, SENSORSAFE will send alarms of
possible unsafe situations. You will be notified when:
• ambient temperature around the clip approaches a
critical level (too high or too low).
• the clip has been buckled for more than two hours.
• the clip has become unbuckled.
• you leave a certain range around your car and the
clip is still closed.
If you stay outside of range for too long and the clip
is still closed, family emergency contacts, that you
designated in the App, will be notified. To ensure
these crticial safety notifications are received, please
designate at least 2 family emergency contacts. You can
find detailed information about the SENSORSAFE App
on www.cybex-online.com.
The SENSORSAFE clip is designed to go into sleep
mode after 12 hours to conserve battery life. To wake it
up, open the clip and buckle it again.
The SENSORSAFE clip should be stored in the
��
unbuckled position while it is not in use to conserve
battery life.

REPLACING THE BATTERY

The SENSORSAFE app shows the battery status of
the clip. Also, the LED on the clip will flash rapidly
after closing when the battery is running low and the
LEDs will not flash at all if the battery is dead. Please
replace the battery in time to be able to connect to
SENSORSAFE.
To replace the battery please open the compartment
located at the rear of the clip with a Philips head
screwdriver (9). Remove the circuit board and old
6
battery. Insert a new CR2032 battery (10) and re-insert
the circuit board into the chest clip with the battery facing
up (11). After changing the battery, you should be able to
connect to the clip in the SENSORSAFE application.
Please consider the following when replacing the
battery:
• Keep all batteries out of reach of children.
• Only use the recommended type CR2032 batteries
(Panasonic or Energizer).
• An empty battery always must be removed in order
to protect the product from escaping liquids.
• Never expose this product or the battery to fire.
• Do not use old batteries or batteries that show signs
of leakage or cracks.
• Only use high-quality new batteries.
• Pay attention to the correct polarity (+/–).

PRODUCT INFORMATION

If you have any questions, contact your retailer first. You
should have the following details ready:
• Serial number of the seat (see sticker on the bottom
of the car seat) and type of the clip (embossing on
the tongue of the clip)
• Weight, age and height of the child
Further information about our products can be found at
www.cybex-online.com
DISPOSAL
To protect the environment, we ask the user to separate
and dispose of the waste arising at the start (packaging)
and the end (product parts) of the SENSORSAFE
clip's lifespan. Waste removal is arranged differently
depending on the local authorities. To ensure that the
clip is disposed of in accordance with regulations,
contact your area's waste removal agency or local
authority. Always observe your country's waste disposal
regulations.
If you do not want to use the clip any longer, return it
free of charge to a recycling depot for used electric
appliances.