Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Strap Keepers: Bundle any excess webbing and secure
it under the elastic strap keepers found on the chest,
shoulder and thigh straps (fig. 25).
WARNING! DORSAL D-RING, CHEST STRAP,
SHOULDER STRAPS AND LEG STRAPS MUST BE
FITTED FOR EACH USER. IMPROPER ADJUSTMENT
AND FIT COULD RESULT IN SERIOUS INJURY OR
DEATH
DONNING THE ERGODYNE
FULL BODY HARNESS
Full body harnesses are the only form of body wear to be
used for fall protection or fall arrest. Proper harness fit is
critical throughout the entire course of the work being
performed near any fall hazard. Do not allow harness
to become loose or slack during use. The following
procedure describes how to properly "don" (put on)
a harness. Please note: Some steps of donning the
harness may require assistance from another person. It is
recommended that, after donning the harness, another
person with knowledge of the safe and correct use of
the harness inspect to ensure the harness is being worn
correctly. The location of the chest, leg and sub-pelvic
straps are critical to the optimal performance of a full
body harness during a fall arrest. An improperly adjusted
or ill-fitting harness could fail during a fall, resulting in
serious injury or death.
Step 1: Fully inspect harness according to
specifications of this instruction manual.
If the full body harness successfully
passes inspection, hold up at D-ring and
ensure all straps are not twisted and all
buckles are unfastened (fig. 26).
FIG. 26
Step 2: Place harness shoulder straps
over shoulders. Ensure dorsal D-ring faces
out and is adjusted to rest between the
middle of the shoulder blades (fig. 27).
FIG. 27
Step 3: Connect thigh straps around
thighs and ensure the webbing is not
twisted (fig. 28).
FIG. 28
Step 4: Adjust chest strap height to lower
chest level, approximately 6-8" from the
top of shoulders and trachea. Connect
chest strap and ensure the webbing is not
twisted (fig. 29).
FIG. 29
8
FIG. 25
Step 5: Adjust leg and shoulder straps so
they fit snugly but still allow for full range
of movement. Adjust the chest strap to
keep the shoulder straps taught. Thigh
straps should never dangle or hang loose.
Fold any extra strap and tuck it into the
strap keepers on the shoulder, thigh and
FIG. 30
chest straps (fig. 30).
WARNING! IT IS EXTREMELY IMPORTANT THAT THE
FULL BODY HARNESS FITS CORRECTLY AND IS
PROPERLY ADJUSTED. PROPER CONNECTION OF
ALL BUCKLES AND FIT OF THIGH, SHOULDER AND
CHEST STRAPS IS ESSENTIAL. AN IMPROPERLY
ADJUSTED OR ILL-FITTING HARNESS COULD FAIL
DURING A FALL, RESULTING IN SERIOUS INJURY
OR DEATH.
WARNING! NEVER ALTER OR MODIFY A HARNESS.
ALWAYS SELECT A HARNESS THAT FITS PROPERLY
WITHOUT MODIFICATION.
WARNING! ON ALL HARNESS STRAPS WITH
FRICTION-STYLE BUCKLES, THE STRAP END
MUST EXTEND A MINIMUM OF 3IN (76MM)
BEYOND THE BUCKLE.
WARNING! ALWAYS CHECK VISUALLY TO ENSURE
THAT BUCKLES ARE FULLY CLOSED BEFORE USE.
CLEANING, MAINTENANCE & STORAGE
Cleaning: Cleaning after use is important for maintaining
the safety and longevity of the Ergodyne Full Body
Harness. Spot clean and rinse the harness with plain water
and a mild soap solution to remove all dirt, corrosives
and contaminants from the harness before and after each
use. Water used for wash and rinse must not exceed 160
degrees Fahrenheit. Wipe off hardware with a clean, dry
cloth. NEVER clean the Ergodyne Full Body Harness with
any corrosive substance.
Maintenance: If the Ergodyne Full Body Harness fails
inspection in any way, immediately remove it from service
and contact Ergodyne to inquire about its return or repair.
Additional maintenance and servicing procedures beyond
spot cleaning with plain water and a mild soap solution
must be completed by a factory authorized service center.
Authorization must be in writing from Ergodyne. Do not
attempt to disassemble the unit.
Storage: Store and transport the Ergodyne Full Body
Harness in a cool, dry, clean environment out of direct
sunlight. Avoid areas where chemical vapors may exist.
Thoroughly inspect the harness after extended storage.
ANNEX A: NORMATIVE
ANSI/ASSE Z359 Requirements for Proper Use and
Maintenance of Full Body Harnesses
(Note: These are general requirements and information
provided by ANSI/ASSE Z359, the Manufacturer of this
equipment may impose more stringent restrictions
on the use of the products they manufacture, see the
Manufacturer's instructions.)
1. It is essential that the users of this type of equipment
receive proper training and instruction, including
detailed procedures for the safe use of such
equipment in their work application. ANSI/ASSE
Z359.2, Minimum Requirements for a Comprehensive
Managed Fall Protection Program, establishes
guidelines and requirements for an employer's
Tabla de contenido
