High Altitude Operation - Ryobi RY80940 Serie Manual Del Operador

 Do not allow the high pressure hose to be kinked.
 Keep hose away from hot surfaces and sharp edges.
 Do not pull unit by high pressure hose.
 Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 17 - 19.
As sold, this unit is designed for use with "downstream"
pressure washer detergents. To convert for use with
"upstream" detergents, contact an authorized customer
service center for more information.
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS; Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump.
Many detergents may require mixing prior to use. Prepare
cleaning solution as instructed on the solution bottle. Always
test in an inconspicuous area before beginning.
 Remove the cap from the detergent tank and pour pressure
washer detergent in the tank. Replace cap on tank.
NOTE: The machine setting of this unit is 20:1, which
usually allows the use of 1 gallon pressure washer
detergent without further dilution. Check your detergent
instructions to be sure additional dilution is not necessary.
 Install 5-in-1 Change Over Nozzle (if necessary). Rotate
the spray selector on the nozzle to either the blue short
range detergent ( ) or blue long range detergent ( )
setting.
 Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
 Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
For long range detergent application:
With the nozzle installed on the spray wand and the engine
shut off, rotate the spray selector to the long range detergent
[ ] setting.
For short range detergent application:
With the nozzle installed on the spray wand and the engine
shut off, rotate the spray selector to the short range detergent
[ ] setting.
Before shutting off the engine:
 Fill the detergent tank with clean water.
All manuals and user guides at all-guides.com
OPERATION
13 — English
 Spray the clear water through the spray wand until the
tank is empty.
 If any soap remains in the spray, repeat with a second
tank of clean water.
 Shut off the engine.
NOTE: Shutting OFF ( O ) the engine WILL NOT relieve
pressure in the system. Pull trigger to release water
pressure.
RINSING WITH THE PRESSURE WASHER
 Turn off the pressure washer and shut off the water supply.
Pull trigger to release water pressure.
 Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
 Select the right nozzle setting for the job. See the chart
on the previous page for selecting the appropriate nozzle
setting.
 When using these settings, test a small area first to avoid
surface damage.
 Start at the top of the area to be rinsed and work down,
overlapping the strokes.
MOVING THE PRESSURE WASHER
See Figure 20.
NOTE: Never lift or carry this product using the handle and
never place the unit in any position other than upright on
its wheels.
 Turn the pressure washer off and ensure the fuel valve is
closed.
 Pull the handle up until the handle release knob snaps into
the locking position (if not already up and locked). Ensure
the lock is secured in the frame hole before moving.
 Tilt the machine toward you slightly until it balances on
the wheels then roll the machine to the desired position.
Do not tilt forward or sideways when moving.
 DO NOT attempt to move the unit by pulling on any of
the hoses.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation.
Please contact your authorized service center for important
information regarding these modifications. Operating this
engine without the proper altitude modification may increase
the engine's emissions and decrease fuel economy and
performance.