Optional Accessories - Makita DF010D Manual De Instrucciones

Nominal diameter of wood screw
(mm)
3.1 (1/8")
3.5 (9/64")
3.8 (5/32")
4.5 (11/64")
4.8 (3/16")
5.1 (13/64")
5.5 (7/32")
5.8 (7/32")
6.1 (15/64")
Drilling operation
First, turn the adjusting ring so that the pointer points to
the marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained
with wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer
at the point to be drilled. Place the point of the bit in the
indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
CAUTION:
• Pressing excessively on the tool will not speed
up the drilling. In fact, this excessive pressure
will only serve to damage the tip of your bit,
decrease the tool performance and shorten the
service life of the tool.
• There is a tremendous force exerted on the tool/
bit at the time of hole break through. Hold the
tool firmly and exert care when the bit begins to
break through the workpiece.
• A stuck bit can be removed simply by setting
the reversing switch to reverse rotation in order
to back out. However, the tool may back out
abruptly if you do not hold it firmly.
• Always secure small workpieces in a vise or
similar hold-down device.
• If the tool is operated continuously until the
battery cartridge has discharged, allow the tool
to rest for 15 minutes before proceeding with a
fresh battery.
Recommended size of pilot hole
(mm)
2.0 - 2.2 (5/64" - 3/32")
2.2 - 2.5 (3/32" - 3/32")
2.5 - 2.8 (3/32" - 7/64")
2.9 - 3.2 (7/64" - 1/8")
3.1 - 3.4 (1/8" - 9/64")
3.3 - 3.6 (1/8" - 9/64")
3.7 - 3.9 (9/64" - 5/32")
4.0 - 4.2 (5/32" - 11/64")
4.2 - 4.4 (11/64" - 11/64")
Using the tool as a hand screwdriver
Switch off the tool.
Move the lock button to the locked position A.
Turn the tool.
NOTE:
• Use the tool with a fastening torque less than 5
Nm (3.7 ft•lbs).
• This use is convenient for checking the
screwdriving.
• Do not use the tool for work requiring excessive
force, such as tightening bolt M6 or bolts greater than M6 or removing rusted screws.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before attempt-
ing to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
• These accessories or attachments are recom-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
8 ENGLISH