Optional Accessories - Makita DDF484 Manual De Instrucciones

Installing driver bit holder
Optional accessory
Fig.11: 1. Driver bit holder 2. Driver bit
Fit the driver bit holder into the protrusion at the tool foot
on either right or left side and secure it with a screw.
When not using the driver bit, keep it in the driver bit holders. Driver bits 5 mm-long can be kept there.
OPERATION
CAUTION:
Al w ays insert the battery cartridge
all the w ay until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of the
tool, causing injury to you or someone around you.
CAUTION:
W hen the speed comes do w n
extremely, reduce the load or stop the tool to
avoid the tool damage.
old the tool firmly with one hand on the grip and the
other hand on the bottom of the battery cartridge to
c o n t r o l t h e t w i s t i n g a c t i o n .
Fig.12
Screw driving operation
CAUTION:
Adjust the adjusting ring to the
proper torque level for your w ork.
CAUTION: Make sure that the driver bit is
inserted straight in the scre w head, or the scre w
and/or driver bit may be damaged.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE: W h e n d r i v i n g w o o d s c r e w , p r e - d r i l l a p i l o t h o l e
/ the diameter of the screw. It makes driving easier
and prevents splitting of the workpiece.
Drilling operation
First, turn the adjusting ring so that the arrow points to
marking. Then proceed as follows.
t h e
Drilling in w ood
When drilling in wood, the best results are obtained
with wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the drill bit into
t h e w o r k p i e c e .
Drilling in metal
To prevent the drill bit from slipping when starting a
hole, make an indentation with a center-punch and
hammer at the point to be drilled. Place the point of the
drill bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
CAUTION:
Pressing excessively on the tool
w ill not speed up the drilling. In fact, this excessive
pressure will only serve to damage the tip of your drill
bit, decrease the tool performance and shorten the
service life of the tool.
old the tool firmly and exert care
CAUTION:
w hen the drill bit begins to break through the
w orkpiece. There is a tremendous force exerted on
the tool/drill bit at the time of hole break through.
CAUTION:
A stuck drill bit can be removed
simply by setting the reversing s w itch to reverse
rotation in order to back out. Ho w ever, the tool
may back out abruptly if you do not hold it firmly.
CAUTION:
Al w ays secure w orkpieces in a
vise or similar hold-do w n device.
CAUTION:
If the tool is operated continuously
until the battery cartridge has discharged, allo w
the tool to rest for 15 minutes before proceeding
w ith a fresh battery.
MAINTENANCE
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use w ith your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Drill bits
Driver bits
Driver bit holder
ook
Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
8 ENGLISH