DeWalt D25832 Traducido De Las Instrucciones Originales página 22

EnGLIsH
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Side Handle (Fig. B)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle 12 clamps to the front of the gear case and
may be rotated 360˚ to permit right- or left-hand use.
Mounting the Side Handle Assembly (Fig. B)
1. Widen the ring opening
14
by rotating the screw for side handle mounting
counterclockwise.
2. Slide the assembly onto the nose of the tool, through the
steel ring and onto the collar
14
and sleeve.
3. Rotate the side handle assembly to the desired position.
4. Lock the side handle mounting assembly in place by
securely tightening the screw for side handle mounting
rotating it clockwise so that the assembly will not rotate.
Bit and Bit Holder

WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small bits of
broken material may damage bare hands.

WARNING: Do not attempt to tighten or loosen chisel bits
(or any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck and
personal injury may occur.
The chipping hammer can be fitted with various chisel bits
depending on the desired application. Use sharp bits only.
Inserting and Removing SDS MAX Bits (Fig. C)
nOtE: Accessories and attachments used must be lubricated
around the SDS fitment before installation.
1. Pull back the locking sleeve 6 and insert the bit shank. The
bit shank must be clean.
2. Turn the bit slightly until the sleeve snaps back into position.
3. Ensure the bit is properly engaged.
nOtE: The bit needs to move several centimeters in and out
of the tool holder 5 when properly engaged.
4. To remove the bit, pull back the locking sleeve and pull the
bit out.
Bit Position Adjustment
Turn the mode selector to bit adjustment icon (Refer to Mode
Selection) to adjust the chisel to the desired position. There are
multiple positions to set the angle of the chisel.
20
of the side handle
12
13
, past the chisel holder
2
13
nOtE: After finding the desired position, slightly maneuver
the chisel bit back and forth to ensure the chisel is
properly engaged.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the mounted side
handle 12 , with the other hand on the main handle
Mode Selection (Fig. A)

WARNING: Do not select the operating mode when the
tool is running. Tool must come to a complete stop before
activating the mode selector button or damage to the tool
may result.
Your tool is equipped with a mode selector dial
mode appropriate to desired operation.
symbol Mode
Bit
adjustment
Hammering/
chipping
To Select a Mode
• Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
nOtE: The arrow on the mode selector dial
at a mode symbol at all times. There are no operable positions
in between.
Indexing the Chisel Position (Fig. A)
The chisel can be indexed and locked into 18 different positions.
1. Rotate the mode selector switch
the position.
2. Rotate the chisel in the desired position.
3. Set the mode selector switch
Chipping" position.
4. Twist the chisel until it locks in position.
4 .
3 to select the
application
Chisel bit position adjustment
Light chipping, chiseling
and demolition
3 must be pointing
3 until it points towards
3 to the "Hammering/