DeWalt DCF894 Traducido De Las Instrucciones Originales página 33

2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 5
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 12 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Belt Hook (Optional Accessory) (Fig. A)

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook for
tethering or securing the tool to a person or object during
use. DO NOT suspend tool overhead or suspend objects
from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.

CAUTION: To reduce the risk of personal injury or
damage, DO NOT use the belt hook to hang the drill
while using as a spotlight.
IMPORTanT: When attaching or replacing the belt hook
only the screw 10 that is provided. Be sure to securely tighten
the screw.
The belt hook can be be attached to either side of the tool
9
using only the screw provided, to accommodate left- or
10
right- handed users. If the belt hook is not desired at all, it can
be removed from the tool.
To move the belt hook , remove the screw
9
place then reassemble on the opposite side. Be sure to securely
tighten the screw.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch
the tool off, release the trigger switch. Your tool is equipped
with a brake. The chuck will stop when the trigger switch is
fully released.
The variable speed switch enables you to start the application at
a slow speed. The further you squeeze the trigger, the faster the
tool will operate. For maximum tool life, use variable speed only
for starting holes or fasteners.
and firmly pull the battery pack
, use
9
that holds it in
10
1 . To turn
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right side of
the tool.
To select reverse, depress the forward/reverse control button on
the left side of the tool. The centre position of the control button
locks the tool in the off position. When changing the position of
the control button, be sure the trigger is released.
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Worklight (Fig. A)
There is a worklight located on the foot of the tool. The
7
worklight will be activated when the trigger switch is depressed.
When the trigger is released, the worklight will stay illuminated
for up to 20 seconds. If the trigger switch remains depressed,
the worklights will remain on.
nOTE: The worklight is for lighting the immediate work surface
and are not intended to be used as a flashlight.
Mode Selector (Fig. A, C)
Your tool is equipped with a mode selector
to select low, high, or Precision Wrench™ mode.
Select the mode based on the application and control the speed
of the tool using the variable speed trigger
Precision Wrench™ (Fig. C)
In addition to low speed impacting modes, this tool features
the Precision Wrench™ mode which grants the user greater
control in both fastening and loosening applications. When set
in forward, the tool will fasten at 2000 RPM until impact begins.
The tool will then pause for 0.5 seconds before continuing
to impact at a rate of 3100 IPM, providing the user with
greater control and reducing the chance of overtightening or
damaging material.
When set in reverse, the tool will impact at a normal speed and
rate of 3100 IPM. Upon sensing that the fastener has broken
free, the tool will cease to impact and will reduce speed to help
prevent "run-off" of loose hardware.
DCF894/DCF894H
Low Mode Low Speed Impacting
High Mode High Speed Impacting
Precision Wrench™ Mode Precision Wrench™
Anvils (Fig. A, D, E)

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessories prior to use to ensure that it con tains
no cracks.
EnGLIsH
2 determines the direction of
8 which allows you
1 .
RPM 0–900
RPM 0–2000
RPM 0–2000
31