Additional Safety Rules - Makita 5604R Manual De Instrucciones

ENGLISH
1 To avoid kickback, do support
board or panel near the cut.
2 Don't support board or panel
away from the cut.
3 A typical illustration of proper
hand support and workpiece
support.
4 Hex wrench
5 Shaft lock
6 Tighten
7 Loosen
SPECIFICATIONS
Model
Blade diameter ................................................... 165 mm
Max. cutting depth
At 90° ................................................................. 54 mm
At 45° ................................................................. 35 mm
-1
No load speed (min ) ............................................ 5,000
Overall length ..................................................... 320 mm
Net weight ............................................................. 3.6 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for performing lengthways and cross-
ways straight cuts and miter cuts with angles to 45° in
wood while in firm contact with the workpiece.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Wear hearing protection.
2. Keep Guards In Place and In Working Order.
Never wedge or tie lower guard open. Check
operation of lower guard before each use. Don't
use if lower guard does not close briskly over
saw blade.
CAUTION: If saw is dropped, lower guard may be
bent, restricting full return.
3. Do not use blades which are deformed or
cracked.
4. Do not use blades of high speed steel.
5. Do not stop the blades by lateral pressure on the
saw blade.
6. Keep Blades Clean and Sharp.
Sharp blades minimize stalling and kickback.
6
Explanation of general view
8 Saw blade
9 Outer flange
10 Inner flange
11 Outer flange
12 Hex socket head bolt
13 Saw blade
14 Setting protuberances
15 Hex socket head bolt
(For adjusting riving knife)
16 Cutting depth
17 Thumb nut
7.
5604R
8.
9.
10. Guard Against Kickback. (Fig. 1 & 3)
11. Lower Guard.
12. Adjustments.
13. Use Only Correct Blades In Mounting.
14. Avoid Cutting Nails.
18 Thumb nut
19 For 45° bevel cuts
20 For straight cuts
21 Base plate
22 Lock-off button
23 Switch trigger
24 Vacuum cleaner
25 Limit mark
26 Brush holder cap
27 Screwdriver
DANGER:
Keep Hands Away From Cutting Area.
Keep hands away from blades. Don't reach
underneath work while blade is rotating. Don't
attempt to remove cut material when blade is
moving.
CAUTION: Blades coast after turn off.
Support Large Panels. (Fig. 1 & 2) Large panels must be supported as shown in
Fig. 1 to minimize the risk of blade pinching and
kickback.
When cutting operation requires the resting of
the saw on the workpiece, the saw shall be
rested on the larger portion and the smaller
piece cut off.
Use Rip Fence.
Always use a fence or straight edge guide when
ripping.
Kickback occurs when the saw stalls rapidly and
is driven back towards the operator. Release
switch immediately if blade binds or saw stalls.
Keep blades sharp. Support large panels as
shown in Fig. 1.
Use fence or straight edge guide when ripping.
Don't force tool. Stay alert–exercise control.
Don't remove saw from work during a cut while
the blade is moving.
NEVER place your hand or fingers behind the
saw. If kickback occurs, the saw could easily
jump backwards over your hand, possibly caus-
ing severe injury.
Raise lower guard with the retracting handle.
Before cutting be sure depth and bevel adjust-
ments are tight.
Don't use blades with incorrect size holes. Never
use defective or incorrect blade washers or
bolts.
Inspect for and remove all nails from lumber
before cutting.