Additional Safety Rules For Charger & Battery Cartridge - Makita BSR730 Manual De Instrucciones

Ocultar thumbs Ver también para BSR730:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 36
ENGLISH
1 To avoid kickback, do support
board or panel near the cut.
2 Don't support board or panel
away from the cut.
3 A typical illustration of proper
hand support and workpiece
support.
4 Button
5 Battery cartridge
6 Battery charger
7 Charging lights
8 Terminal cover
9 Hex wrench
0 Loosen (counterclockwise)
q Shaft lock
SPECIFICATIONS
Model
Blade diameter ............................................. 190 mm
Max. cutting depth
At 90° ......................................................... 66 mm
At 45° .......................................................... 47 mm
At 50° .......................................................... 42 mm
–1
No load speed (min
) ..................................... 2,400
Overall length ............................................... 378 mm
Net weight ....................................................... 4.6 kg
Rated voltage ............................................ D.C.24 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
6
All manuals and user guides at all-guides.com
Explanation of general view
w Saw blade
e Outer flange
r Bolt
t Inner flange
y Setting protuberances
u Hex socket head bolt
i Cutting depth
o Lever
p Clamp screw
a Lever
s Slant surface
d Base
f Adjusting screw for 90°
g Adjusting screw for 45°
h Triangular rule
7. Make sure cord is located so that it will not be
BSR730
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has received a
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
10. Do not disassemble charger or battery car-
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
11. To reduce risk of electric shock, unplug
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
12. The battery charger is not intended for use by
young children or infirm persons without
supervision.
13. Young children should be supervised to
ensure that they do not play with the battery
charger.
ENC002-2
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
2. Do not attempt to use a step-up transformer,
an engine generator or DC power receptacle.
3. Do not allow anything to cover or clog the
charger vents.
j For 45° bevel cuts
k For straight cuts
l Base plate
; Cutting line
z Lock-off button
x Switch trigger
c Rip fence (Guide rule)
v Dust nozzle
b Screws
n Hose 28 mm in inner dia.
m Vacuum cleaner
, Limit mark
. Brush holder cap
/ Screwdriver
Tabla de contenido
loading

Tabla de contenido