Technical Data - Makita BCM2600 Manual De Instrucciones

Maintenance instructions
- The condition of the Brush Cutter/String Trimmer must be checked before operation, in particular of the cutting tool, the protective devices and also the
shoulder strap. Special attention must be paid to the cutting blade which must be correctly sharpened.
- Stop the engine and remove spark plug connector when replacing or sharpening cutting tools, and also when cleaning the machine or cutting tool.
- Operate the Brush Cutter/String Trimmer with as little noise and contamination as possible. In particular check the correct setting of carburetor.
- Clean the Brush Cutter/String Trimmer regularly and ensure that all screws and nuts are well tightened.
- Never service or store the Brush Cutter/String Trimmer in the vicinity of naked flames.
- Always store the Brush Cutter /String Trimmer in locked rooms and with a emptied fuel tank.
- Do not perform any modifications on the Brush Cutter/String Trimmer as this will endanger your safety.
- The performance of maintenance or repair work by the user is limited to those activities as described in this instruction manual. All other works are to be
done by an Authorized Service Agent. Use only genuine spare parts and accessories supplied by MAKITA.
Use of non-approved accessories and tools means increased risk of accidents.
MAKITA will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and fixing devices of cutting tools, or
accessories.
First Aid
Make sure that a first-aid box is available in the vicinity of the cutting operations in case of accident.

TECHNICAL DATA

MODEL
Dry Weight
Engine
Bore x Stroke
Displacement
Maximum output
Fuel
Lubricating oil
Fuel Tank Capacity
Spark Plug
Carburetor
Main Pipe Drive Shaft Flex/Rigid
Tube
Bearings
String Head
Gear Case Assy
Clutch Case Assy
Throttle Control
Hanger
Guard
Handle Assy
Band Shoulder
Tool Set
Blade
Blade Holder
BCM2310/CA
5.7 kg
TLE23FD-TBM/TBD
31 x 30 mm
22.6 cm
0.7 kW (0.94 HP)/
8000 rpm
Diameter
Upper end
Lower end
Type
Diameter
Wall thickness
Length
Finish
Type
Type
O.Dia.
Line size
Arbor size
Gear ratio
Anti-Vib
Number Brgs
Drum dia.
Overmolded
First Idle
Type
Type
Swath dia 41 cm (16 in.)
Type
Barrier
Overmolded
Type
Size
Type
BCM2610/CA
5.7 kg
TLE26FD-TBM/TBD
33 x 30 mm
3
25.6 cm
0.8 kW (1.07HP)/8000 rpm
Mixture of gasoline and lubricanting oil (ratio 50:1)
Two-stroke motor oil FC
0.6 lit.
NGK BPMR8Y
Diaphragm type (with 2 passage for air and mixture)
7 mm Hollow (5 mm)
Involute Spline (7 x 7 x 0.75)
25.4 mm
1500 mm
Silver Anodized
Bronze bush in rubber
Tap and Go
105 mm
2.4 mm
M10LH FEM
14/19
54 mm
Grass
43 cm (17 in.)
Loop
Yes (Black)
Single
N/A
N/A
7
BCM2600 BCM3310/CA
6.5 kg 6.5 kg
TLE33FD-TBM/TBD
3
0.97 kW (1.3 HP)/7500 rpm
Rigid
Straight
1.5 mm
Tap and Go
N/A 105 mm
2.4 mm
17/21
Yes
2
Yes
Yes
Fixed
Weed Blade Grass
N/A 43 cm (17 in.)
Bike Loop
N/A
N/A Yes (Black)
Yes
23 cm (9 in.)
N/A
Quard
Yes N/A
BCM3300
7.3 kg
36 x 32 mm
3
32.6 cm
0.8 lit.
N/A
78 mm
Weed Blade
N/A
Bike
N/A
Double
23 cm (9 in.)
Quard
Yes