Operation - EINHELL TE-CS 18/165-1 Li Solo Manual De Instrucciones Original

develop a defect.
Dans l'intérêt d'une longue durée de fonctionne-
ment du bloc accumulateur, vous devez prendre
soin de recharger le bloc accumulateur en temps
voulu. Ceci est dans tous les cas indispensable
lorsque vous constatez une diminution de la
puissance de l'appareil. Ne déchargez jamais
complètement le bloc accumulateur. Ceci cause
l'endommagement du bloc accumulateur !
5.7 Battery capacity indicator
(Fig. 10 – Item h)
Press the battery capacity indicator switch (i). The
battery capacity indicator (h) shows the charge
status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

Warning!
Always remove the battery pack before making
adjustments to the equipment.
6.1 Working with the hand-held circular saw
•
Always hold the tool firmly by the handles
provided (1 and 10) to ensure that you handle
it safely when using it.
•
The swing guard hood (19) is pushed back
automatically by the workpiece.
•
Do not use force!
•
Push forwards gently and evenly with the
circular saw.
•
The waste piece should be on the right-hand
side of the circular saw so that the wide
section of the support bench supports its full
area.
•
If you are sawing down a line that has been
drawn, guide the circular saw along the corre-
sponding notch.
•
Clamp small pieces of wood securely before
Anl_TE_CS_18_165-1_Li_Solo_SPK9.indb 24 Anl_TE_CS_18_165-1_Li_Solo_SPK9.indb 24
GB
sawing them. Never hold them with your
hand.
•
Always follow the safety instructions. Wear
safety goggles.
•
Do not use defective saw blades or blades
that are cracked or broken.
•
Do not use any flanges / flange nuts whose
bore hole is larger or smaller than those in the
saw blade.
•
The saw blade must not be decelerated by
hand or by applying lateral pressure to the
blade.
•
Check that the swing guard hood works pro-
perly. The swing guard hood must not jam,
and it must return to its initial position when
you have completed the cut.
•
Before you use the circular saw, check the
function of the swing guard hood with the
mains plug disconnected.
•
Before you use the machine, ensure that the
safety equipment such as the swing guard
hood, flanges and adjustment devices are in
working order and are correctly adjusted and
secure.
•
You can connect a suitable dust extraction
system to the sawdust extraction connector
(14). Ensure that the dust extractor line is sa-
fely and correctly connected.
•
The moving swing guard hood must not be
fixed in the retracted guard hood when the
saw is in use.
6.2 Using the circular saw
•
Adjust the cutting depth, cutting angle and
parallel stop (see section 5.1, 5.2 and 5.4)
•
Do not switch on the circular saw until you
have fitted a saw blade.
•
Place the saw foot flat on the workpiece you
wish to saw. The saw blade must not be in
contact with the workpiece.
•
Hold the circular saw firmly with both hands.
6.3 Switching ON/OFF (Fig. 12)
To switch on:
Press the locking button (3) and the ON/OFF
switch (2) at the same time
•
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Only exert gentle
pressure on the saw blade as you do so.
- 24 -
09.12.2019 09:14:56 09.12.2019 09:14:56