Tabla de contenido
Idiomas disponibles
Idiomas disponibles
interrupting a cut for any reason, release
the trigger and hold the saw motionless
in the material until the blade comes to a
complete stop. Never attempt to remove
the saw from the work or pull the saw
backward while the blade is in motion or
kickback may occur. Investigate and take
corrective actions to eliminate the cause of
blade binding.
c) When restarting a saw in the
workpiece, center the saw blade in the
kerf and check that saw teeth are not
engaged into the material. If saw blade is
binding, it may walk up or kickback from the
workpiece as the saw is restarted.
d) Support large panels to minimize the
risk of blade pinching and kickback.
Large panels tend to sag under their own
weight. Supports must be placed under the
panel on both sides, near the line of cut and
near the edge of the panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades
produce narrow kerf causing excessive
friction, blade binding and kickback.
f) Blade depth and bevel adjusting
locking levers must be tight and secure
before making cut. If blade adjustment
shifts while cutting, it may cause binding and
kickback.
g) Use extra caution when making a
"plunge cut" into existing walls or other
blind areas. The protruding blade may cut
objects that can cause kickback.
LOWER GUARD SAFETY INSTRUCTIONS
a) Check lower guard for proper closing
before each use. Do not operate the saw
if lower guard does not move freely and
close instantly. Never clamp or tie the
lower guard into the open position. If saw
is accidentally dropped, lower guard may be
bent. Raise the lower guard with the
retracting handle and make sure it moves
freely and does not touch the blade or any
other part, in all angles and depths of cut.
b) Check the operation of the lower
guard spring. If the guard and the spring
are not operating properly, they must be
serviced before use. Lower guard may
operate sluggishly due to damaged parts,
gummy deposits, or a buildup of debris.
c) Lower guard should be retracted
manually only for special cuts such as
"plunge cuts" and "compound cuts."
Raise lower guard by retracting handle
and as soon as blade enters the material,
the lower guard must be released. For all
other sawing, the lower guard should
operate automatically.
d) Always observe that the lower guard
is covering the blade before placing saw
down on bench or floor. An unprotected,
coasting blade will cause the saw to walk
backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to
stop after switch is released.
ADDITIONAL SAFETY INSTRUCTIONS
• Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
or against your body leaves it unstable and
may lead to loss of control.
• Keep your body positioned to either
side of the blade, but not in line with the
saw blade. KICKBACK could cause the
saw to jump backwards (see Causes and
Operator Prevention of Kickback and
KICKBACK).
• Avoid cutting nails. Inspect for and
remove all nails from lumber before
cutting.
• Always make sure nothing
interferes with the movement of the
lower blade guard.
• Accessories must be rated for at least
the speed recommended on the tool
warning label. Wheels and other
accessories running over rated speed can
fly apart and cause injury. Accessory ratings
must always be above tool speed as shown
on tool nameplate.
• Always make sure the saw is clean before
using.
• Stop using this saw and have it properly
serviced if any unusual noise or abnormal
operation occurs.
• Always be sure all components are
mounted properly and securely before
using tool.
• Always handle the saw blade with care
when mounting or removing it or when
removing the diamond knockout.
• Always wait until the motor has reached
full speed before starting a cut.
• Always keep handles dry, clean and free of
oil and grease. Hold the tool firmly with both
hands when in use.
• Always be alert at all times, especially
during repetitive, monotonous operations.
Always be sure of position of your hands
relative to the blade.
• Stay clear of end pieces that may fall after
cutting off. They may be hot, sharp and/or
heavy. Serious personal injury may result.
• Replace or repair damaged cords. Make
sure your extension cord is in good
condition. Use only 3-wire extension
cords that have 3-prong grounding-
type plugs and 3-pole receptacles that
accept the toolʼs plug.
4
Tabla de contenido
