Adjusting The Handle - Chicco Best Friend Instrucciones De Uso

All manuals and user guides at all-guides.com
FASTENING THE CHILD CAR SEAT INSIDE
THE VEHICLE
5. Position the handle of the child car seat ver-
tically by pressing the two side adjustment
buttons (Fig. 8).
6. Position the child car seat on the car seat
where you intend to install it (Fig. 9).
7. Pull the car's safety belt and fasten it in the
relevant buckle by passing the waist belt
through the two blue guides on the side of
the Child Car Seat (Fig. 10).
8. Hold the chest belt and pull it, tensioning the
waist belt (Fig. 11). At the end of the opera-
tion, check that the waist belt is always in the
relevant blue belt guides.
9. Always keeping the chest belt tensioned,
pass it through the blue guides on the back
of the backrest (Fig. 12). Pull the belt as tight-
ly as possible without leaving any slack and
making sure it is not twisted.
WARNING! After installing the child car seat,
always check that the vehicle safety belt is
tightened and that the buckle does not force
the belt to come out of the relevant slot. Also
check that the buckle of the car belt is not in
contact with the point of passage of the belt
on the child car seat. These situations may
compromise the effectiveness of the child car
seat in the event of an accident.
WARNING! Never fit the seat belt in any way
not mentioned in this instruction booklet, as it
would compromise the child's safety!
POSITIONING THE CHILD
10. Press the aluminium button in the front part
of the Child Car Seat (covered by the fabric)
and loosen the two shoulder straps on the
Child Car Seat while holding it down (Fig. 13).
11. Unfasten the fastening buckle of the safety
harness, pressing the red button (Fig. 14).
12. Place your child in the child car seat and
then fasten the safety harness (Fig. 15). The
shape of the forks is designed that it does
not allow inserting one of the two forks
in the buckle; they both need to be over-
lapped before inserting in the buckle.
13. Adjusting the tension of the child's safety
harness by pulling on the relevant adjust-
ment belt (Fig. 16) making sure not to tight-
en the child too much.

ADJUSTING THE HANDLE

The child car seat handle can be adjusted to 3
different positions:
- Carrying position (Fig. 17)
- Rest position (Fig. 18)
- Baby reclined cradle stabiliser position (Fig. 19)
To switch from one position to another, press the
two buttons on the lateral joints of the handle.
ROCKER POSITION (USE AS BABY Reclined
cradle )
When the child car seat is not used in a car, it
can be used as a rocker or baby reclined cradle.
To make it rock, position the handle in the rest
position.
To make it stationary, position the handle in the
baby reclined cradle stabiliser position.
IMPORTANT! KEEP FOR FUTURE REFERENCE.
WARNING: BEFORE USE, REMOVE AND DIS-
POSE OF ALL PLASTIC BAGS AND PACKAGING
MATERIALS AND KEEP THEM OUT OF REACH OF
CHILDREN.
WARNINGS
• WARNING: Age range intended for use: from
birth to 9 kg (6 months).
• WARNING: Never leave the child unattended
• WARNING: Do not use the reclined cradle
once your child can sit unaided, roll over or
stand up pushing on their hands, knees and
feet.
• WARNING: This reclined cradle is not intended
for prolonged periods of sleeping
• WARNING: It is dangerous to use this reclined
cradle on an elevated surface, e.g. a table.
• WARNING: Always use the restraint system.
• Always use the restraint system when your
child is in the baby reclined cradle; adjust the
length of the straps as necessary.
• WARNING: The baby reclined cradle does
not replace a bed or a crib. Then it should be
placed in a suitable bed or cradle.
• WARNING: Do not use the baby reclined cra-
dle if any components are broken or missing
• WARNING: Do not use accessories or re-
placement parts other than those approved
18