Century 1010 Manual Del Usuario página 5

Engage starter for 3-4 seconds; if engine fails to start,
charge the battery for another 5-15 minutes and attempt
to start the engine again.
Select "10A, 12 V Auto" if you are charging large lead acid
batteries such as those used in automobiles, boats,
trucks, vans, farm equipment, etc.
Select "2 A, 12 V" for charging lawn tractor, motorcycle,
snowmobile, or other small batteries. Do not use this
setting for large automotive, truck or marine batteries.
Select "10 A, 6 V" for charging 6 volt batteries used in
automobiles, trucks, and farm equipment. This setting
does not taper. NOTE: The 10 A, 6 V position does not
shut-off automatically.
MODEL 87120
Select "70 A Start" if you
are attempting to start a
car with a weak battery.
Note: for best results,
first charge battery,
using directions above,
70 AMP
for 5 - 15 minutes.
START
Crank engine for 3-4
seconds. If engine fails
to start, charge battery for another 5-15 minutes and
attempt to start the engine again.
Select "12 A" if you are charging large lead acid batteries
such as those used in automobiles, boats, trucks, vans,
farm equipment, etc.
Select "2 A" for charging lawn tractor, motorcycle,
snowmobiles, or other small batteries.
After you have read the owner's manual and
completed the steps required in sections "A" through
"J", the charger can be plugged in and used!
MODEL 87128
Charging A Battery-Starting an Engine
This charger is equipped with Auto On-Off Technology
which senses when a battery has reached full charge and
then shuts the charger off automatically (12-V selections
only). Note: Charger will continue to hum as it monitors
battery charge level.
Select 12 A, 12 V AUTOMATIC DEEP CYCLE position if
you are charging a lead acid deep cycle battery.
NOTE: The MANUAL charging positions do not shut off
automatically. Only the AUTOMATIC charging positions
will shut off automatically.
Select either 12 A, 12 V position if you are charging large
lead acid batteries such as those used in automobiles,
boats, trucks, vans, farm equipment, etc.
Select either 2 A, 12 V position for charging lawn tractor,
motorcycle, snowmobile, or other small batteries. Do not
use this setting for large automotive, truck or marine
batteries.
All manuals and user guides at all-guides.com
SELECT SETTING
12A 2A OFF
Select 12 A, 6 V MANUAL position for charging 6 V
batteries used in automobiles, trucks, and farm
equipment. This setting does not taper. NOTE: The
MANUAL charging positions do not shut-off automatically.
Step 1: CHARGING A BATTERY
Rotate the selector switch from OFF to the desired voltage
and amperage level to charge a battery. There is only one
position available (12A 6V MANUAL) for charging 6 volt
batteries. Automatic positions are available for charging
12 volt batteries only.
Note: Preactivation of a low or dead battery may be
required.
To preactivate a battery, rotate the selector switch to the
70A 12V position (70A 12V ENGINE START/ACTIVATE).
Charge the battery in that position for 5-15 minutes then
select the desired charge rate to continue charging.
Repeat if the battery does not start to charge.
12A 12V
AUTOMATIC
DEEP CYCLE
12A 12V
AUTOMATIC
70A 12V
2A 12V
AUTOMATIC
ENGINE START/
ACTIVATE
Step 2: Starting a vehicle
Note: for best results, first charge battery, using directions
in Step 1, for 5-15 minutes.
Rotate the selector switch to the 70A 12V position (70A
12V ENGINE START/ACTIVATE) for assistance in starting
an engine with a weak battery.
Crank engine for 3 seconds. If engine fails to start, charge
battery for another 5 to 15 minutes and attempt to start
the engine again.
After you have read the owner's manual and
completed the steps required in sections "A" through
"J", the charger can be plugged in and used.
MODEL 87122
Charging A Battery
This charger is equipped with Auto On-off Technology
which senses when a battery has reached full charge and
5
OFF 12A 6V
MANUAL
12A
12V
MAN.
2A 12V
MANUAL
E
n
g
l
i
s
h