Century 1010 Manual Del Usuario página 4

E J
n
g
Model No. Page
l
1010 4
i 1014 4
1050 4
s
1060 4
h
MODEL 1014 &
87104
Select "6V, 10 Amp" for manual
charging of 6-volt batteries used
in automobiles, trucks and farm
equipment. Note: The 6V, 10
Amp position is manual only
and does not taper.
Select "12V, 2 Amp" for
charging lawn tractor, motorcycle, snowmobile or other
small batteries.
Select "12V, 10 Amp for charging large lead acid batteries
used in automobiles, boats, trucks, vans, farm equipment,
etc.
Note: Discontinue charging within 24 hours of battery
reaching full charge.
MODEL 87102 & 1010
Select "10 A, 12 V" if you are charging large lead acid
batteries such as those used in automobiles, boats,
trucks, vans, farm equipment,
etc.
Select "2 A, 12 V" for charging
lawn tractor, motorcycle,
snowmobile, or other small
batteries.
Select "10 A, 6 V" for charging
6 volt batteries used in automobiles, trucks, and farm
equipment. This setting does not taper.
After you have read the owner's manual and
completed the steps required in sections "A" through
"J", the charger can be plugged in and used!
MODEL 87105 &1050
Select "55 A Start" if you are attempting to start a car with
a weak battery. Note: for best results, first charge battery
for 5 - 15 minutes. Crank engine for 3-4 seconds; if engine
fails to start, charge the battery for another 5-15 minutes
and attempt to start the engine
again.
Select "10 A, 12 V" if you are
charging large lead acid
batteries such as those used in
automobiles, boats, trucks,
vans, farm equipment, etc.
All manuals and user guides at all-guides.com
OPERATING INSTRUCTIONS
TABLE OF CONTENTS
Model No. Page
1150 5
1160 6
1200 6
87102 4
87104 4
SELECT SETTING
OFF 10A 2A 10A
12V 12V 6V
AUTOMATIC MANUAL
SELECT SETTING
OFF 10A 2A 10A
12V 12V 6V
SELECT SETTING
55 AMP 10A 2A 10A
START 12V 12V 6V
Model No. Page
87105 4
87106 4
87120 5
87128 5
Select "2 A, 12 V" for charging lawn tractor, motorcycle,
snowmobile, or other small batteries.
Select "10 A, 6 V" for charging 6 volt batteries used in
automobiles, trucks, and farm equipment. This setting
does not taper. After you have read the owner's
manual and completed the steps required in sections
"A" through "J", the charger can be plugged in and
used!
MODEL 87106, 1060
&YA510B
Charging a Battery-Starting an Engine
This charger is equipped with Auto On-off Technology
which senses when a battery has reached full charge and
then shuts the charger off automatically (12-V settings
only). Note: Charger will continue to "hum" as it monitors
battery charge level.
Step 1: SELECT FUNCTION (Switch 1)
Note: Preactivation of a
low or dead battery may be
required.
Select START. Charge for
5-15 minutes then select
the desired charge rate to
continue charging. Repeat
if the battery does not start taking a charge.
Select "Charge" if you will be charging a battery.
Select "Start" if you are attempting to start a car with a
weak battery. After you have read the owner's manual
and completed the steps required in sections "A"
through "J", the charger can be plugged in and used.
Step 2: SELECT SETTING (Switch 2)
Select "55 A Start" if you
are attempting to start a
car with a weak battery.
Note: for best results, first
charge battery, using
directions in Step 1, for 5-
15 minutes.
4
Model No. Page
87122 5
87150 6
87151 6
87302 6
YA510B 4
SELECT FUNCTION
CHARGE START
SELECT SETTING
55 AMP 10A 2A 10A
START 12V 12V 6V