Makita DLS713 Manual De Instrucciones página 21

In the case of left bevel cut
Molding
position in
52/38°
Fig.43 & 44
For
(1)
inside
corner
(2)
33.9°
(3)
For
outside
(4)
corner
Molding
position in
Fig.43 & 44
(1)
For inside
corner
(2)
(3)
For outside
corner
(4)
EXAMPLE In the case of cutting 52/38° type crown
molding for position (1) in Fig.43 & 44:
• Tilt and secure bevel angle setting to 33.9°
LEFT.
• Adjust and secure miter angle setting to 31.6°
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on
the saw.
• The finished piece to be used will always be
on the LEFT side of the blade after the cut has
been made.
In the case of right bevel cut
Molding
position in
52/38°
Fig.43 & 44
For
(1)
inside
corner
(2)
Right
33.9°
(3)
For
outside
(4)
corner
Table (A)
Bevel angle Miter angle
45° 52/38°
type type type
Right
31.6°
Left Left
Left 30°
31.6°
Right
31.6°
Table (B)
Molding edge
Finished
against guide
piece
fence
Ceiling
contact edge
Finished
should be
piece will be
against guide
on the Left
fence.
side of blade.
Wall contact
edge should
be against
guide fence.
Finished
Ceiling piece will be
contact edge on the Right
should be side of blade.
against guide
fence.
Table (A)
Bevel angle Miter angle
45° 52/38°
type type type
Right
31.6°
Right Left
30° 31.6°
Right
31.6°
45°
type
For inside
Right
corner
35.3°
Left
35.3°
Right
For outside
35.3°
corner
EXAMPLE In the case of cutting 52/38° type crown
molding for position (1) in Fig.43 & 44:
• Tilt and secure bevel angle setting to 33.9°
RIGHT.
• Adjust and secure miter angle setting to 31.6°
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its WALL
CONTACT EDGE against the guide fence on
the saw.
• The finished piece to be used will always be on
the RIGHT side of the blade after the cut has
been made.
Wood facing
Use of wood facing helps to assure splinter-free cuts
in workpieces. Attach a wood facing to the guide fence
using the holes in the guide fence.
See the figure concerning the dimensions for a sug-
gested wood facing.
► Fig.45: 1. Holes
CAUTION:
ness as the wood facing.
WARNING:
facing to the guide fence. The screws should be
installed so that the screw heads are below the
surface of the wood facing so that they will not
interfere with the positioning of the material being
cut. Misalignment of the material being cut can case
45°
unexpected movement during the cutting operation
type
which may result in a loss of control and serious
Right
personal injury.
35.3°
NOTICE: When the wood facing is attached, do not turn
Left
the turn base with the handle lowered. The blade and/or
35.3°
the wood facing will be damaged.
Right
35.3°
Cutting repetitive lengths
CAUTION:
ers and the holder assemblies as standard acces-
sories, this type of use is not permitted due to the
country regulations.
21 ENGLISH
Table (B)
Molding Molding edge
position in against guide
Fig.43 & 44 fence
Wall contact
edge should
(1)
be against
guide fence.
(2) Ceiling
contact edge
should be
(3)
against guide
fence.
Wall contact
edge should
(4)
be against
guide fence.
Use the straight wood of even thick-
Use screws to attach the wood
For the tool equipped with the hold-
Finished
piece
Finished
piece will be
on the Right
side of blade.
Finished
piece will be
on the Left
side of blade.