Tabla de contenido
Idiomas disponibles
Idiomas disponibles
8.
Be careful not to drop, shake or strike battery.
9.
Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.
ADDITIONAL SAFETY RULES FOR TOOL
1.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
2.
Rags, cloth, cord, string and the like should
never be left around the work area.
3.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
4.
Use only sharp blades. Handle the blades very
carefully.
5.
Be sure the blade installation bolts are securely
tightened before operation.
6.
Hold the tool firmly with both hands.
7.
Keep hands away from rotating parts.
8.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.
• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into
place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted
correctly.
Charging (Fig. 2)
Plug the fast charger into the proper AC voltage source. The charging light will flash in green color. Insert the battery
cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective mark-
ings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the bat-
tery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging
light will remain lit steadily during charging. When the charging light color changes from red to green, the charging
cycle is complete. Refer to the table below for the charging time. If you leave the battery cartridge in the charger after
the charging cycle is complete, the charger will switch into its "trickle charge (maintenance charge)" mode which will
last approximately 24 hours. After charging, unplug the charger from the power source.
Battery type
1202, 1202A, 1222
1200, 1220
1233
1234
1235
CAUTION:
• The fast charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's
batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it
may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-
tery cartridge fully after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location
exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a
while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you remove the
battery cartridge from the fast charger.
6
All manuals and user guides at all-guides.com
9.
10. Wait until the blade attains full speed before cut-
11. Keep at least 200 mm away from the tool at all
12. Always switch off and wait for the blades to
ENB043-1
13. Never stick your finger into the chip chute. Chute
14. Do not leave the tool running. Operate the tool
15. When leaving the planer, switch off and set it
16. Always change both blades or covers on the
17. Wait for complete run-down before putting the
18. Use only Makita blades specified in this manual.
SAVE THESE INSTRUCTIONS.
Capacity (mAh)
2,000
1,300
2,200
2,600
3,000
Make sure the blade is not contacting the work-
piece before the switch is turned on.
ting.
times.
come to a complete stop before any adjusting.
may jam when cutting damp wood. Clean out
chips with a stick.
only when hand-held.
with the front base up on a wooden block, so
that the blades do not contact anything.
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
tool aside.
Number of cells
10
10
10
10
10
Charging time
Approx. 45 min.
Approx. 30 min.
Approx. 50 min.
Approx. 60 min.
Approx. 70 min.
Tabla de contenido
