Recording From A Video Cassette Recorder; Manual Recording - Panasonic DMR-E500H Manual De Instrucciones

Recording from a video cassette recorder

DVD
TV
DIRECT TV REC
AV
HDD, DVD
HDD
1 2
4 5
7 8
CANCEL
0
SKIP
STOP
∫
DIRECT NAVIGATOR
TOP MENU
3,4,2,1
ENTER
SUB MENU
PROG/CHECK
DISPLAY
TIMER ERASE
F
REC MODE
EXT LINK DUBBING
A
e.g., Connecting other video equipment to the AV3 or DV input
terminals
≥Turn off the unit and other video equipment before connecting.
This unit
EJECT
PC CARD
SD CARD
HDD
S-VIDEO IN VIDEO IN L/MONO AUDIO IN R DV IN
AV3
VIDEO IN L/MONO - AUDIO IN - R
S-VIDEO IN
Yellow White Red
S-Video Audio/
§
Video cable
cable
If the audio output of the other equipment is monaural, connect to L/MONO.
§
The S-VIDEO terminal achieves a more vivid picture than the
VIDEO terminal.
DV automatic recording (DV AUTO REC) (➡page 52)
When recording from the unit's DV terminal
Select the type of audio recording from "Audio Mode for DV Input" in
the SETUP menu (➡page 64).
All manuals and user guides at all-guides.com
VOLUME
CH
DVD SD/PC
3
CH
6
ShowView
9
INPUT SELECT
MANUAL SKIP
INPUT SELECT
SLOW/SEARCH
PAUSE PLAY/x1.3
;
FUNCTIONS
FUNCTIONS
ENTER
RETURN
STATUS TIME SLIP
REC MODE REC
¥ REC
CREATE
AUDIO
CHAPTER
AUDIO
B C
OPEN/CLOSE
TIME SLIP HDD DVD SD PC DRIVE SELECT
DVD
DV IN
DV cable
(IEEE 1394, 4-pin)
Other video
equipment

Manual recording

[HDD] [RAM] [DVD-R]
Preparation
≥Connect a video cassette recorder to this unit's input terminals.
≥Press [HDD] or [DVD] to select the recording drive.
≥To adjust the audio recording level (➡ below)
≥When recording bilingual programmes
[HDD] [RAM]
When both M 1 and M 2 is selected on the connected equipment,
you can select the audio type in playback.
([HDD] When simultaneously recording by MPEG4 format, select
either M 1 or M 2 on the connected equipment)
[DVD-R]
Select either M 1 or M 2 on the connected equipment.
≥When the output signal from the external equipment is NTSC,
change the "TV System" to "NTSC" in the SETUP menu (➡page 67).
≥To reduce noise in input from a video cassette recorder, set "AV-in
NR" to "On" in the SETUP menu (➡ page 63).
1
While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
e.g., If you have connected to AV3 input terminals, select "AV3".
2
Press [REC MODE] to select the
recording mode.
3
Start play on the other equipment.
4
Press [¥ REC].
Recording starts.
To skip unwanted parts
Press [;] to pause recording. (Press again to restart recording.)
To stop recording
Press [∫].
To record programmes to fill up the remaining space on the disc
/ x 1.3
➡ page 26, Flexible Recording
∫ To adjust the audio recording level
1 Before recording commences, press and hold [AUDIO] for
more than 3 seconds.
Audio REC Level
L
L 0
L/R
R 0
R
CH SELECT
ENTER
2 Press [3, 4] to select "L/R".
To individually adjust a level press [3, 4] to select "L" (left) or "R"
(right).
≥If "L" (left) and "R" (right) cannot be selected with [3, 4], press
[AUDIO] to switch the audio.
3 Press [2, 1] to adjust the audio recording level and press
[ENTER].
≥Set the level to neutral again after finishing recording as other
recordings will also be affected.
≥If the recording level is too high the audio will be distorted. Set it so
the audio level meter is not shaking. (Maximum –10 dB to –5 dB is
an appropriate level)
≥The DV input is unaffected.
Almost all videos and DVD software on sale have been
treated to prevent illegal copying. Any software that has
been so treated cannot be recorded using this unit.
-¶
30 20 15 10 5 0 OVER
ADJUST
RETURN
RQT7751
51
51