Functional Description - Makita BPT350 Manual De Instrucciones

17. Never drive fastener into any materials which may
allow the fastener to puncture and fly through as a
projectile.
18. Never actuate the switch trigger and safety lever
at the same time until you are prepared to fastener
workpieces. Allow the workpiece to depress the
safety lever. Never defeat its purpose by securing
the safety lever back or by depressing it by hand.
19. Never tamper with the safety lever. Check the
safety lever frequently for proper operations.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter,
stop operating immediately. It may result in a risk
of overheating, possible burns and even an
explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
All manuals and user guides at all-guides.com
2. Never recharge a fully charged battery cartridge.
3. Charge the battery cartridge with room
4. Charge the battery cartridge once in every six

FUNCTIONAL DESCRIPTION

• Always be sure that the tool is switched off and the
Installing or removing battery cartridge
(Fig. 1)
• Always switch off the tool before installing or removing
ENC007-7
• To remove the battery cartridge, slide it from the tool
• To install the battery cartridge, align the tongue on the
• Do not use force when installing the battery cartridge. If
Safety system
• Make sure all safety systems are in working order
Test safety systems for possible faulty operation before
pin-nailing as follows.
1. Make sure that the tool is not loaded with pin nails
2. Pull the sliding door of the magazine toward yourself.
3. The tool accidentally operates if only the trigger is
4. The tool does not operate when the trigger is pulled
In case of 3 and 4 above, the safety systems are faulty.
Trigger and lever
• Before inserting the battery cartridge into the tool,
The tool is provided with lever as a safety system in
addition to the usual trigger. (Fig. 5)
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
Overcharging shortens the battery service life.
temperature at 10°C - 40°C (50°F - 104°F). Let a hot
battery cartridge cool down before charging it.
months if you do not use it for a long period of
time.
CAUTION:
battery cartridge is removed before adjusting or
checking function on the tool.
of the battery cartridge.
while sliding the button on the front of the cartridge.
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If you can see the red indicator
on the upper side of the button, it is not locked
completely. Install it fully until the red indicator cannot
be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
the cartridge does not slide in easily, it is not being
inserted correctly.
WARNING:
before operation. Failure to do so may cause personal
injuries. (Fig. 2)
before the test.
(Fig. 3)
pulled although the lever is not pulled.
with the lever pulled.
CAUTION:
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released. (Fig. 4)
5