Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Long lasting operation at low rotational speed of the spindle may
cause motor overheating. Make periodic breaks in operation or allow
the tool to operate at top speed without load for approximately 3
minutes.
HOLDER
The power tool provides convenient holder (6) that allows to e.g.
hang the tool on a tool belt when working at heights.
OPERATION AND MAINTENANCE
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the power tool, battery and charger with a dry cloth or blow
through with compressed air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Clean ventilation holes in the motor casing regularly to prevent
device overheating.
• In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a qualified
person.
• Store the power tool and its equipment in a dry place, beyond
reach of children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by
the manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless impact driver 58G024
Parameter
Battery voltage
Max. torque (gear I / II / III)
Range of spindle rotational speed
without load (gear I / II / III)
Range of impact rate (gear I / II / III) 0-1400 / 0-2520 / 0-3780 min
Tool holder
Protection class
Weight
Year of production
58G024 defines type and indication of the device
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Value
18 V DC
80 / 120 / 200 Nm
0-1000 / 0-1800 / 0-2700 rpm
-1
Hexagonal 6.35 mm (¼")
III
1.1 kg
2019
Value
58G001
58G004
18 V DC
18 V DC
Li-Ion
Li-Ion
2000 mAh
4000 mAh
4
C – 40
C
4
C – 40
C
0
0
0
0
1 h
2 h
0,400 kg
0,650 kg
2019
2019
14
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Noise and vibration information
Parameters of produced noise level, such as sound pressure level
Lp
and sound power level Lw
with measurement uncertainty K are
A
A
specified below in this manual, in compliance with EN 60745.
Vibration values a
and measurement uncertainty K are determined
h
in accordance with EN 60745-2-2 and specified below.
Vibration level specified below in this manual was measured in
accordance with measurement procedure defined in EN 60745 and
can be used to compare power tools. It can also be used for initial
assessment of exposure to vibrations.
Specified vibration level is representative for main applications
of the power tool. Vibration level may change if the power tool is
used for other purposes, with different working tools or will not
be maintained properly. The abovementioned factors may lead to
higher exposure to vibrations during whole working time.
To precisely define exposure to vibrations, include periods when the
power tool is switched off and when it is switched on but not used for
working. This way total exposure to vibrations may be significantly
lower. Use additional safety measures to protect the user against
results of exposure to vibrations, such as: power tool and working
tool maintenance, proper hand temperature conditions, good work
organisation.
Sound pressure level: Lp
= 69 dB (A) K=3dB (A)
A
Sound power level: Lw
= 80 dB (A) K=3dB (A)
A
Vibration acceleration: a
= 3,845 m/s
h
ENVIRONMENTAL PROTECTION
Electrical equipment must not be disposed off
with household waste and, instead, should be
utilized at appropriate facilities. Information
on utilization can be provided by the product
vendor or the local authorities. Waste electrical
and electronic equipment contains substances
that are not neutral to the natural environment.
Equipment that is not recycled constitutes a
potential hazard to the environment and to
human health.
Storage batteries/batteries must not be disposed
with domestic waste, put in a fire or into the
water. Damaged or used up storage batteries
must be properly recycled in compliance with the
current directive pertaining to disposal of storage
batteries and batteries.
Li-Ion
* Right to introduce changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa
with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs,
that all copyrights to this instruction (hereinafter Instruction), including, but not
limited to, text, photographies, schemes, drawings and layout of the instruction,
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4
C – 40
C
0
0
1 h
2 h
II
0,300 kg
2019
K = 1,5 m/s
2
2
Tabla de contenido
