Operation And Maintenance - GRAPHITE 58G013 Manual De Instrucciones

página de 105

/ 105
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

SELECTION OF WORKING TOOL

With this cordless multi tool you can use working tools

compatible with universal, open attachment system (with 9

holes). Holes, 2 mm in diameter, are located around 10 mm

radius circle every 30° (some holes can also form an open cut

out).

Below table presents examples of various working tools.

Name

Type of material

HSS blade

Metal

(e.g.

for metal

bolts,

small

tions), non-ferrous

metals

H a l f - r o -

Wood, wood-based

und

HCS

materials, plastics

wheel for

wood

HCS blade

Wood, wood-based

for wood

materials, plastics

H a l f - r o -

Cement joints, soft

und wheel

ceramic tiles, hard

with tung-

plastics and other

sten grit

materials.

Delta san-

Wood, wood-based

ding pad

materials, abrasive

materials.

Stiff scra-

Linings, floors, cera-

per

mic tiles.

INSTALLATION OF WORKING TOOLS

• Pull the lever for quick working tool installation (1) forward

(fig. D).

• Slide working tool between two plates of the tool holder, make

sure the holes are matched with pins of the upper washer.

• In order to allow operation in the position that is most comfortable

and safe for the operator, you can set up the working tool in the

tool holder in a position of your choice, provided that the upper

plate pins are matched with the holes (fig. E).

• Working tool should be installed with bend pointing down.

• Lower the lever for quick tool installation (1) to install the working

tool in selected position (fig. D).

Check that the tool is installed properly. Improperly or

inaccurately installed working tools can slip during operation and

cause risk for the user.

DUST EXTRACTION

Dust of some materials may be hazardous to health, like paint

coatings with lead additives, some types of wood e.g. oak or

beech or materials with asbestos. Therefore, we recommend use

of external dust extraction systems, good workplace ventilation

and use of dust-mask with particle filter.

The tool is equipped with dust extraction add-on, which should be

connected to external dust extractor, e.g. vacuum cleaner designed

for the type of produced dust.

Intended use

Example

nails,

Small dividing and

Cutting narrow

sec-

plunge cutting.

sections short,

cutting joining

elements, e.g.

clamps.

Dividing and plun-

Narrow plunge

ge cutting in cor-

cuts in solid

ners and hard to

wood, e.g. for

reach areas, near

air grates.

surfaces.

Dividing and plun-

Cut outs in fur-

ge cutting in cor-

niture boards,

ners and hard to

cutting

cove

reach areas, near

bases

short,

surfaces.

plunge cutting

for fitting floor

panels.

Cutting short and

Removal

cutting off close to

joint,

cutting

edges, in corners

holes in cera-

and hardly acces-

mic tiles and

sible places.

plastics.

Sanding in hard to

Removal

reach areas and in

mortar

and

corners on a hard

glue for ce-

substrate.

ramic

tiles,

sanding solid

wood,

poli-

shing.

Scraping soft ma-

Removal

terials on a hard

mortar

resi-

substrate.

dues, glue for

lining or cera-

mic tiles.

REMOVING THE DUST EXTRACTION ADD-ON

• Remove working tool if already installed.

• Disengage the clamp (3) and remove the dust extraction add-on

(6).

Installation of the dust extraction add-on (6) is similar to

deinstallation, only the sequence of actions is reversed.

OPERATION / SETTINGS

Check condition of the working tools before using the power tool.

Do not use tools with dents, cracks or other damages. Replace

worn out tools with new ones before operation. When the work

is finished, always turn the device off and wait until the working

tool comes to complete stop. Only then you can put the device

away. Do not brake the working tool when it's moving by pressing

it against processed material.

SWITCHING ON / OFF

Hold the device with both hands when starting up and during

operation.

Switching on – slide the switch (2) forward to position I.

Switching off – slide the switch (2) backward to position O (fig. F).

Each time you press the switch button (2) two LED diodes (13) turn

on. They are located on both sides of the head and illuminate the

work place.

ROTATIONAL SPEED CONTROL

Wheel for rotational speed control (4) is located at the bottom part

of the main handle (fig. G). Control range is 1 to 6. Rotational speed

can be adjusted to the user's needs.

Do not cover holes for motor ventilation in the tool body.

PRINCIPLES OF OPERATION

Oscillation frequency 5 000 – 20 000 per minute at 3° angle allows to

work precisely in small areas and corners with the power tool.

OSCILLATION FREQUENCY 5 000 – 20 000 PER MINUTE AT 3°

ANGLE ALLOWS TO WORK PRECISELY IN SMALL AREAS AND

SAWING AND CUTTING

Use only undamaged working tools in good technical condition.

When sawing or cutting wood, fibre board, wood-based materials

etc. make sure they do not contain foreign objects like nails, bolts

etc. before starting the task. Remove foreign objects or use proper

blade for removal. You can make plunge cuts only in soft materials

like wood, gypsum boards and alike. Cutting ceramic tiles causes

faster wear of working tool.