Preliminary Operations; Electrical Connection - Cuppone Silea Guia De Inicio Rapido

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 12
Installazione
Installation
Transport
EN
Fig.1.
Fitted with personal protection equipment,
transport the appliance to the installation location.
Use suitable equipment, capable of dealing with its weight:
persons not involved with the appliance installation may not pass
through or stand in the work area during the appliance assembly.
During the transport, pay particular attention to passing through
openings and/or doors.
Model
SILEA 20
SILEA 30

Preliminary operations

Fig.2.
Carefully remove the protective film.
If any glue residue is left on the surfaces, remove it with soapy
water but without any corrosive or abrasive products or sharp or
pointed instruments.
Check that all the parts making up the product are in
good condition and without any faults or breakages, if
that is not the case, contact the Retailer for the procedures
to follow.
Positioning
Fig.3.
Install the appliance in a room:
• dedicated and suitable to the cooking of food;
• having adequate air ventilation;
• containing no flammable or explosive elements;
• that complies with the current regulations on health and
safety and systems in your country;
• is protected from the weather;
• has a maximum temperature of between +5° (41°F) and +35°C
(95°F);
• has a maximum humidity of 70%.
To reduce the risk of a fire,
minimum distances
fireproof
rooms and
of the installation room must also have a
Serial number plate reading
Fig.4.
The serial number is on the back of the appliance.
It provides important technical information that is vital in case of
a request for maintenance or repair of the appliance: please do
not remove, damage or modify it.
Installation
Instalación
Weight
80 kg [176,3 lb]
103 kg [227 lb]
comply with the stated
and install the appliances in
not at risk of
explosion. The floor
fireproof
surface finish.
Installation
Установка

Electrical connection

The electrical connection must be carried out
by qualified personnel after reading the safety warnings
at the beginning of the manual.
Before installing the appliance,
comply with the regulations in force
where it is going to be used and
indicated on the appliance rating plate
product.
have the power cable already installed; a plug
• machines
(not supplied) must be fitted to it
This operation must be carried out by qualified personnel.
For a correct electrical connection, the appliance must:
equipotential system
• be included in an
compliance with the legislation in force. This connection
must be made between the various devices with the terminal
marked with the equipotential symbol
have a maximum cross-section of 10 mm
IEC EN 60335-2-42:2003-09) and must be yellow-green;
grounded
• must be
• must be connected to a
the regulations in force (0.03A A type);
• must be connected to an
complete disconnection in overvoltage III category conditions.
The Manufacturer accepts no liability for failure to comply with
the above.
If required, the cable must be replaced by the Dealer or its
technical service or by a person with similar qualifications
to prevent any risk.
Pre-testing and final inspection
The product is checked and tested in the Manufacturer's plant
before being delivered to the customer.
The "production process check sheet" enclosed with it guarantees
that each step in the production process, from assembly to
packaging, was carefully checked from both the operating and
safety standpoints.
Operations to carry out before delivery of the product to the
customer.:
• Check the direction of rotation of the bowl (indicated by the
arrow on the sticker) is correct
• Start the appliance following the instructions in the "Use and
Maintenance" manual annexed: monitor it during the whole
test and check that all the electrical components work properly.
• At the end of the test, you
IF IT IS NOT REGULARLY ACTIVATED, THE VALIDITY OF
THE SAME STARTS FROM THE INVOICE DATE AND NOT
FROM THE ACTUAL INSTALLATION DATE.
20
exclusively
check that systems
in the country
with the specifications
on the LH side of the
of suitable capacity.
Fig.6.
. The cable must
(in compliance with
2
to the mains (green-yellow wire);
circuit breaker
in compliance with
omnipolar circuit breaker
MUST
activate the guarantee.
in
allowing
Tabla de contenido
loading

Tabla de contenido