DeWalt DCS396 Traducido De Las Instrucciones Originales página 35

Wear eye protection.
Do not expose the power tool to humidity.
Date Code Position (Fig. A)
The date code 17 , which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A, B)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
On/off trigger switch
1
Lock-off button
2
Rear grip handle
3
Front handle
4
Saw blades
5
Intended Use
Your D WALT alligator saw has been designed for professional
e
sawing applications of clay building blocks, cellular concrete,
wood, plastic and insulation materials with suitable saw blade.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These alligator saws are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
Bar
6
Hex key
7
Dust port
8
Battery
9
Battery release button
10
WALT battery packs and chargers.
9 is fully charged.
To Install the Battery Pack into the Tool Handle
1. With tool off, align the battery pack
the tool's handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button . A combination of the three green LED lights will
18
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Replacing the Saw Blades
Removing the Saw Blades (Fig. C–F)
1. Place the tool upside down on a flat, stable work surface.
2. Loosen the gearcase cap screw
When loosened, the gearcase cap
spring open.
3. With the hex key 7 , loosen both of the blade setting
screws 13 . The screws will be held in place by the
screw clips.
4. Carefully pull the saw-blade-end up until it is disengaged
from and clear of the Blade-Clamp-system.
5. Pull the saw blade back and out of the front guard
take it off of the bar 6 .
6. Repeat this procedure for the other saw blade.
Fitting the Saw Blades (Fig. D, F)
1. Slide one saw-blade into the blade guide slot
sure that the end with the slotted hole
guard 14 .
2. Slide the back of the saw blade down until the threaded
hole 15 aligns with the blade setting screw
3. Repeat this procedure for the other saw blade.
4. Tighten both saw blade setting screws
pressing and turning simultaneously with the short end of
the hex key .
7
5. Close the gearcase cap 12
cap screw.

WARNING: Before operation let the saw blades run freely
for approx. 20 s.
EngLIsh
9 with the rails inside
10 and firmly pull the
11 with the hex key 7 .
should release and
12
and
14
19 making
fits into the front
16
13 .
13 securely by
and tighten the gearcase
33