Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). The minimum conductor
2
size is 1.5 mm
. When using a cable reel, always
unwind the cable completely.
Also refer to the table below.
2
Conductor size (mm
)
Cable rating (Amperes)
0.75
6
1.00
10
1.50
15
2.50
20
4.00
25
Cable length (m)
7.5
Voltage
Amperes
Cable rating (Amperes)
230
0 - 2.0
6
2.1 - 3.4
6
3.5 - 5.0
6
5.1 - 7.0
10
7.1 - 12.0
15
12.1 - 20.0
20
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Replacing the collet assembly (fig. B)
Your laminate trimmer is supplied with an 8 mm
collet fitted to the tool. Two other precision collets
are also available to suit the cutter used. The collet
and the collet nut are inseparable.
• Keep the spindle lock button (13) depressed and
loosen the collet nut (12) completely.
• Remove the collet assembly.
• Fit a new assembly and screw the collet nut onto
the spindle. Do not tighten.
Inserting and removing a cutter (fig. C)
• Keep the spindle lock button (13) depressed and
loosen the collet nut (12) with the wrench.
• Insert a cutter (14) and tighten the collet nut.
Never tighten the collet nut without a
cutter in the collet.
16
15
25
30
45
60
6
6
6
6
6
6
6
6
6
6
6
6
6
10
15
10
10
10
15
15
15
15
15
20
20
20
20
20
25
-
Setting the depth of cut (fig. D)
• Turn the plunge lock (3) counterclockwise to
release the carriage.
• Set the required depth of cut by turning the
depth stop adjuster (2) to the desired setting on
the scale.
• To fine-tune the depth of cut, use the ring on the
adjuster.
• Tighten the plunge lock (3).
Mounting and adjusting the copy follower
(fig. A, E1 - E7)
The copy follower (9) is used to trim along shaped
edges (fig. E1 & E2).
• Mount the copy follower (9) by inserting the guide
rods (8) into the corresponding holes in the
trimming base (4) (fig. A).
Height
• Loosen the adjustment lever (15) and move the
copy follower up or down as required (fig. E3).
• Tighten the adjustment lever.
Side distance
• Loosen the clamping nut (16) and set the side
distance using the fine adjuster (17) (fig. E4 & E5).
• Tighten the clamping nut again.
Straight guide or guide roller
The straight guide (18) is used to avoid copying the
imperfections in the edges of the base material
when using the copy follower (9).
• For straight edges, place the straight guide onto
the ball bearing assembly (fig. E7).
• For shaped edges, remove the straight guide
from the ball bearing assembly.
Mounting the trimming plate (fig. F)
The trimming plate (19) is used when trimming
laminates which are higher than the board surface.
• Attach the trimming plate to the tool base as shown.
Removing the motor from the base (fig. G)
• To remove the motor from the base, loosen the
motor clamping lever (6).
Feed direction (fig. H)
• Always feed the workpiece against the rotating
cutter as shown in fig. H.
E N G L I S H
en - 4
Tabla de contenido
