Changing The Filter - Siemens VS08G Serie Instrucciones Para El Uso

en
Vacuuming with accessories
Figure 10
Pull the combination tool in the direction of
the arrow to remove it from the tool holder.
a) Crevice nozzle
For vacuuming in crevices and corners.
For difficult to get to places, the combina-
tion tool can be extended in two stages to
360 mm by pulling out the crevice nozzle.
Extend the crevice nozzle to the second
stop until you can hear it engage.
To push the crevice nozzle together again,
release the telescope lock (by pressing in
arrow direction).
b)Upholstery nozzle
For cleaning upholstery, curtains, etc.
c) Furniture brush
For window frames, cabinets, profiles etc.
Fold the upholstery nozzle over in the
direction of the arrow.
To extend the brush ring, turn in the
direction of the arrow.
Before replacing combination tool in
the tool holder, retract the bush ring
and fold the upholstery nozzle back.
Figure 11*
When you stop cleaning for a moment, you
can use the parking aid at the back of the
vacuum cleaner.
Slide the plastic lug on the nozzle connec-
tor into the groove at the back of the vacu-
um cleaner.
If your cleaner has the automatic Off func-
tion, it will now switch itself off.
=> Power indicator lights up "green".
* Depending on equipment level
When the work is done
Figure 12
Switch the vacuum cleaner off and unplug
the power cord from the mains.
Tug the power cord and let go. The cable
then rewinds automatically.
To reactivate or deactivate the cable brake,
quickly tug the power cord.
On vacuum cleaners with an electronically
actuated cable rewind, the power cord
automatically rewinds when the machine is
unplugged at the socket.
If you do not want the power cord to
rewind completely (e.g. when changing the
plug), you can apply the cable brake by
pulling the power cord.
Figure
13
To store or transport the vacuum cleaner,
you can use the parking aid on the clea-
ner's underside. Place the vacuum cleaner
upright.
Slide the plastic lug on the floor nozzle into
the groove no the unit underside.

Changing the filter

Replacing the MEGAfilt ® SuperTEX dust
bag
Figure 14
If the dust bag change indicator lights
up brightly and uniformly when the
nozzle is lifted from the floor and the
vacuum is on its highest setting, you
should change the dust bag, even if it
is not yet full. In this case it is
essential to change the dust bag due
to the type of material it contains.
Turn the dust compartment locking lever in
the direction of the arrow to open the dust
compartment cover.
Figure 15
Seal the MEGAfilt ® SuperTEX dust bag by
pulling the locking tab and then remove it.
en
Figure 16
Place a new MEGAfilt ® SuperTEX dust bag
in the holder and close the dust bag
compartment cover.
!
Caution: The dust bag compartment
cover will only close when the
MEGAfilt ® SuperTEX dust bag, textile
filter or dust collector has been inserted.
If the dust bag change indicator
continues to light up after the dust
bag has been changed, please
check whether the nozzle, pipe or
vacuum hose are obstructed.
Replacing the motor protection filter
You should change the micro-hygiene filter
with each new replacement filter pack
(at least after every five dust bags).
Figure 17
Open the dust compartment cover (see
figure 14).
Pull the filter holder out in the direction of
the arrow and open it.
Dispose of the motor protection filter and
fit a new motor protection filter.
Close the filter support, slide into the vacu-
um cleaner and close the dust compart-
ment cover.
Replacing the micro-hygiene filter*
You should you change the micro-hygiene
filter with each new replacement filter pack
(at least after every five dust bags).
Figure 18
Press the exhaust grille latch in the direc-
tion of the arrow to unlatch the exhaust
grille and open it.
Press the filter frame latch in the direction
of the arrow to unlatch the filter frame and
remove it.
Figure 19*
Remove the foam and micro-hygiene filter.
Dispose of the micro-hygiene filter and fit a
new micro-hygiene filter.
Clean the foam and replace in the filter
frame.
If you have used the vacuum cleaner for fine
dust particles (such as plaster or cement),
clean the motor protection filter by tapping it
and, if necessary, replace the motor protec-
tion filter and the micro-hygiene filter.
Figure 20*
Remove the activated carbon filter by pul-
ling a tab and dispose of it as normal
waste.
Fit a new activated carbon filter.
Figure 21
Slide the filter frame under the two retai-
ning ribs and turn in the direction of the
arrow until it engages.
Close the exhaust grille.
Replacing the Hepa filter*
If your vacuum cleaner is equipped with a
Hepa filter, you need to replace this filter
once a year.
(For filter replacement, see figures 18 and 21)
Replacing the activated carbon filter*
If your vacuum cleaner is equipped with a
Hepa activated carbon filter, you need to
replace the Hepa filter yearly and the activa-
ted carbon filter twice a year. (For filter repla-
cement, see figures 18, 20 and 21)
Care
Always switch the vacuum cleaner off and
disconnect the power cord from the mains
before cleaning the vacuum cleaner.
The vacuum cleaner and plastic accessories
can be cleaned with a commercial plastic
cleaner.
!
Do not use abrasive, glass or all-purpo-
se cleaners.
Never immerse the vacuum cleaner in
water.
The dust compartment can, if necessary, be
cleaned with a second vacuum cleaner or
simply wiped with a a dry cloth or dusting
brush.
subject to technical changes.